Rigol RP5600A User Manual Download Page 6 | Manualshive

Page: 6 / 22

Rigol RP5600A User Manual Download Page 6

RIGOL

User’s Guide for RP5600A

IV

Contents

Guaranty and Declaration ......................................................... I
General Care and Cleaning ...................................................... III
RP5600A Probe at a Glance ....................................................... 1
General Inspection ................................................................... 2
Accessories ............................................................................. 3
To Connect to the Oscilloscope .................................................. 6
To Use the Probe ..................................................................... 8
Compensation Adjustments ..................................................... 11
Characteristics ....................................................................... 14
Warranty ............................................................................... 15
Contact Us ............................................................................ 16

«
...
4
5
6
7
8
...
»

Summary of Contents for RP5600A























Reviews:

No comments