manualshive.com logo in svg

Rigol RP5600A, User Manual, Page: 11 / 22

Share
Download
Rigol RP5600A User Manual Download Page 11

RIGOL

 

                                                 

User’s Guide for RP5600A   

5 

6.  Dual-lead Adapter 

Lead out a plug from the signal terminal and the ground 
terminal of the probe respectively. 

7.  Probe Bracket 

Lay and fix the probe during the measurement. 

8.  SMD Clip 

Lead out the pin signal of the circuit under test. 

9.  Spring Ground 

Connect to the probe tip for grounding to improve the 
high-frequency response. 

10. Alligator Ground Lead   

Ground the probe reliably for safe operation and accurate 
signal reading. 

11. Socketed Ground Lead 

The usage is the same as the alligator ground lead but it uses 
different joint (refer to the figure of standard accessories). 

12. Screwdriver 

Used in probe compensation adjustment.   

13. Sign Loop 

Fix sign loops of different colors on the probes to distinguish 
the probes connected to different channels. 

14. BNC Adapter                    

Use this adapter to connect the probe to a BNC connector. 
 
 
 
 
 
 

Summary of Contents for RP5600A























Reviews:

No comments