Rigol DL3000 Series User Manual Download Page 47

Page: 47 / 163

Chapter 2 Front Panel Operations

RIGOL

DL3000 User’s Guide

2-17

WARNING

To avoid electric shock, ensure that the DUT is connected to the

input terminals of the load properly before you turn on the channel

input.

CAUTION

When the fan stops working, the channel is disabled. Then, a

message is displayed, "Fan stops running!"

View waveform display

Press the waveform display key

to enter the waveform display interface,

as shown in Figure 2-13. When you select "P" under "Data", you can view the

power waveform. When changes occur to the input voltage, the current changes

linearly to keep the power value unchanged. For detailed operations, refer to the

descriptions in "Waveform Display Function" section. Press the waveform

display key

again to exit the waveform display interface and return to the

main interface of CP mode.

Figure 2-13 Waveform Display Interface of CP Mode

Exit CP mode

Press any key on the front panel of the load to exit CP mode.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands