background image

WELCOME

2

Thank you for choosing to drive more and scale less! Here at Right 

Weigh, we are committed to making our products simple to install and 

easy to use. We understand that installation can vary between vehicles 

and yours may not be described in this manual. In any event, our 

technical support team is ready to answer your questions!  

(503) 628-0838
(888) 818-2058  -  Toll Free (USA ONLY)

[email protected]

www.rwls.com/how-to-calibrate-install/

FOLLOW US!

IMPORTANT!

Please read instructions COMPLETELY and thoroughly before installation. Right 

Weigh, Inc. is not responsible or liable for product failure or vehicle damage due to 

improper installation. The installation requirements are outlined in this manual and 

should be followed thoroughly to avoid inaccuracy or damage to the product.

It is also important to be aware of vehicle manufacturer policies before making 

modifications to the vehicle. Right Weigh, Inc. is not liable or responsible for issues 

regarding warranties with other manufacturers. This is the responsibility of the 

customer. If you are unsure about how these installation practices apply to your 

vehicle, please contact your vehicle or component manufacturer.  

Summary of Contents for 221-SK

















Reviews: