Rev. 1 of 15.04.16
No. 00216
The communication quality with the CP at the place of the detector installation
should provide reliable message transmission (See Cl. 9 Communication Quality
Appraisal).
8 LED Indication
Table 3
Detector Status
LED Indication
LED Status
Operation mode
«Binding»
Green LED indicator blinks
intermittently
«Alarm»*
LED indicator lights red for at
least 0.5 sec
If indication is
enabled
«Identification»
LED indicators blinks alternately
red and green at 1 Hz frequency
by a command
from the CP
«Connection quality»
See Sect. «Communication Quality Appraisal»
Binding procedure
completed
LED indicator lights red for 2 sec
*) — Alarm indication is deactivated in 15 minutes after the detector cover is
closed and activated after it has been opened or at a command from the CP.
10 Installation
10.1 Assemble the supplied swivel bracket:
Figure 3 – The Swivel Bracket Design
Plug
Nut Sphere
Swivel
bracket
Screw
- place the screw-nut into the
sphere recess;
- enclose the swivel bracket
base into the sphere;
- insert the plug into the swivel
bracket base.
10.2 Install and fix the assembled swivel bracket to the wall/ceiling at the
chosen place of installation. The swivel bracket case should be used as a
pattern for marking fixation holes on the installation surface.
10.3 Fix the base to the installed swivel bracket by means of mounting screw
passing it through the one of the openable holes (2).
10.4 After fixing the base on the swivel bracket pack off the opening (2) by
the plastic potting compound (supplied).
10.5 Put the PCB on it’s place, fix it by latch and screw (8).
11 Adjustment
11.1 The detector adjustment includes the detection zone position alignment
and sensitivity level choosing.
11.2 To determine the limits of the detection zone, start movement across the
detection zone at a speed of 0.5 – 1 m/sec 60 sec after switching the detector
in «Activated» mode.
11.3 Upon every detection of a movement, the detector transmits the «Alarm»
message via radio communication. During the first 15 min after the cover
closing, the «Alarm» message is duplicated by the LED indicator switching red
in a short-run.
11.4 Changing of the detection zone position is fulfilled by the detector
rotation on the swivel bracket.
«Alarm» message generation upon the motion absence within the detection
zone limits indicates a high - interference environment. In this case, it is
recommended to narrow the detector sensitivity. Removal of «SENS.HIGH»
jumper reduces the detector detection range from 12 up to 8 m, but in the
same time it increases the detector interference protection. After sensitivity
adjustment, check the detection zone limits.
The «Alarm» indication is switched off automatically in 15 min after the
detector case closing.
If it is necessary to continue the adjustment, put off the cover, and after put
it on it’s place.
Modes of operation
The detector provides three modes of operation: «Deactivated», «Activated»
and «Identification». The modes changeover is ensured by the relevant command
from the CP.
Under operation in the «Deactivated» mode, the detector transmits the
«Alarm» message immediately with contemporary starting unscheduled radio
communication session. «Norm» message is transmitted during regular radio
communication sessions.
Under operation in the «Activated» mode, the detector immediately transmits
messages about it’s state changing with contemporary starting unscheduled
radio communication session.
Under the «Identification» mode, started by the relevant command from
the CP, the LED indicator blinks red and green alternately (See Table 3). The
«Identification» mode allows to locate the detector with the preset address.
12 Storage and Transportation
12.1 The Detectors in original package may be transported by any means
of transportation in closed vehicles over any distances in compliance with the
existing shipping rules concerning the respective means of transportation.
12.2 Storage conditions of the Detectors: storage premises should not
contain any current-conducting dust, acid and alkali fumes, as well as corrosive
gases or those destroying insulation.
13 Manufacturer’s Guarantees
13.1 The manufacturer guarantees conformity of the Detector to the Technical
Specifications requirements provided the transportation, storage, installation
and operation conditions are observed.
13.2 The guaranteed shelf life of the Detector is 63 months since the date
of manufacture.
13.3 The guaranteed useful life is 60 months since the day of putting into
operation within the guaranteed shelf life.
13.4 The Detectors that are found non-conforming to the Technical
Specifications requirements shall be repaired by the manufacturer, provided the
installation and operation rules have been complied.
Note
– Warranty obligations are not applied to the power supply batteries.
14 Acceptance and Packing Certificate
Wireless security passive infrared wide-angle detector «Pyrone-8-RK»,
batch number________________________,
has been manufactured in compliance with the active technical documentation,
classified as fit for operation and packed by «RIELTA» JSC.
Person in charge of acceptance and packing
QC representative_________________ __________________.
day, year, month
Made in Russia
«RIELTA» JSC, www.rielta.com,
Chapaeva Str. 17, Saint Petersburg, Russia, 197101, [email protected],
Tel./fax. +7 (812) 233-0302, 703-1360,
Technical support, tel. +7 (812) 233-29-53, 703-13-57, [email protected]
.