Riello RLS 650/M MX Installation, Use And Maintenance Instructions Download

Page: 47 / 60

20027761

Appendix - Accessories

Output power regulator kit for modulating operation

With the modulating operation, the burner continually adapts the
power to the request for heat, ensuring great stability for the
parameter controlled: temperature or pressure.

Two components should be ordered:
•

the output regulator to install on the burner;

•

the probe to install on the heat generator.

Output power regulator with signal 4-20 mA, 0-10V

Two components should be ordered:
•

the Analogic signal converter;

•

the Potentiometer

Potentiometer kit for the indication of load position

Soundproofing box kit

Kit for the remote fuel selection

Gas trains approved according to EN 676

Refer to the instruction manual.

Appendix - Accessories

Parameter to control

Probe

Output power regulator

Range

Type

Code

Type

Code

Temperature

- 100...+ 500°C

PT 100

3010110

RWF50.2
RWF50.5

20101190
20101191

Pressure

0...2,5 bar

0...16 bar

Probe with output

4...20 mA

3010213
3010214

Burner

Potentiometer

Analogic signal converter

RLS 650/M MX

Type

Code

Type

Code

ASZ...

3010402

E5202

3010390

Burner

Code

RLS 650/M MX

3010402

Burner

Code

RLS 650/M MX

3010376

Burner

Code

RLS 650/M MX

3010372

Summary of Contents for RLS 650/M MX





























































Search results

Summary of Contents for RLS 650/M MX

Reviews:

Related manuals for RLS 650/M MX

Brands by name

Popular brands

Riello RLS 650/M MX, Installation, Use And Maintenance Instructions

Search results

Summary of Contents for RLS 650/M MX

Reviews:

Related manuals for RLS 650/M MX

Brands by name

Popular brands