manualshive.com logo in svg

Riello UPS sentryum S3U, User Manual, Page: 51 / 56

Share
Download
Riello UPS sentryum S3U User Manual Download Page 51

 

- 49 - 

 

PROBLEM 

POSSIBLE CAUSE 

SOLUTION 

THE ALARM LIST SHOWS C06

 

THE JUMPER IS MISSING 

FROM THE R.E.P.O. 

CONNECTOR (REFER TO 

R.E.P.O - “COMMUNICATIONS” 

CHAPTER) OR THE 

CONNECTOR IS NOT 

INSERTED CORRECTLY 

Assemble the jumper or check that it is inserted correctly. 

THE ALARM LIST SHOWS C05

 

MAINTENANCE BYPASS 

BREAKER (SWMB) CLOSED 

OR INTERLOCK PADDLE IS 

NOT IN PLACE 

Verify if manual bypass switch (SWMB) is actually closed and 
why  or  the  interlock  paddle  was  removed  or  misplaced. 
Otherwise contact your local service center. 

THE ALARM LIST SHOWS A01

 

INCORRECT DATA 

CONFIGURATION 

Check the settings. 

THE ALARM LIST SHOWS 

NOTHING OR PROVIDES 

INCORRECT INFORMATION  

THE DISPLAY HAS POWER 

SUPPLY PROBLEMS 

Close the Manual Bypass switch SWMB (if present) keeping 
closed the INPUT and OUTPUT switches. 
Open input switch (SWIN and SWBYP if present) and wait until 
the UPS completely turns OFF. 
Close the SWIN and SWBYP switches again and verify regular 
display operation. Switch off the maintenance bypass. If the 
fault persists, contact the nearest technical support center. 

THE ALARM LIST SHOWS 

ONE OR MORE OF THE 

FOLLOWING CODES: 

F01, F02, F03 

ONE OR MORE PHASES ARE 

SWAPPED 

Check the input and bypass terminal connections. 

THE ALARM LIST SHOWS 

ONE OR MORE OF THE 

FOLLOWING CODES: 

A18 

PROTECTIVE DEVICE 

UPSTREAM FROM THE 

BYPASS LINE OPEN (ONLY IF 

BYPASS IS SEPARATE) 

Reset the upstream protective device. WARNING: check that 
there is no overload or short circuit at the output of the UPS. 

BYPASS SWITCH OPEN 

(SWBYP ONLY IF BYPASS IS 

SEPARATE FROM MAINS) 

Close the bypass switch (SWBYP) if present. 

THE ALARM LIST SHOWS 

ONE OR MORE OF THE 

FOLLOWING CODES: 

F04 

WRONG BATTERY 

CONNECTIONS OR BATTERY 

FUSES BLOWN  

Verify battery connections and, if the connections are correct, 
replace the battery fuses. 
WARNING: if necessary, we recommend to replace fuses only 
with others of the same type. (for further information refer to 
the Installation manual). 

THE ALARM LIST SHOWS 

ONE OR MORE OF THE A09 

CODE

 

THE BATTERIES FAILED THE 
PERIODIC EFFICIENCY TEST 

The batteries of the UPS should be replaced as they are no 
longer  able  to  maintain  the  charge  for  a  sufficient  time  to 
ensure the required autonomy. 

WARNING: The batteries are to be replaced by qualified 
staff.

 

THE ALARM LIST SHOWS 

ONE OR MORE OF THE 

FOLLOWING CODES: 

L01 

FAULT AT THE UPS INPUT 

STAGE

 

Activate the maintenance bypass SWMB (if present), turn the 
UPS off and on again. If the problem persists, call your local 
service center. 

 

 

Summary of Contents for sentryum S3U

























































Reviews:

No comments