background image

5

1200 Series SmartPanels 1.0  User Manual

0

1

-0

0

0

H

B

0

3

E

G

-A1

0

1.1

Information

Symbols

The following tables are used to indicate hazards and provide cautionary information in relation to the
handling and use of the equipment.

Danger

!

Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.

The highlighted line indicates the activity to prevent the danger.

Warning

!

Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.

The highlighted line indicates the activity to prevent the danger.

Caution

!

Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices.

The highlighted line indicates the activity to prevent the danger.

This text is for generally information. It indicates the activity for ease of work or for better
understanding.

Service

·

All service has to be undertaken ONLY by qualified service personnel.

·

There are no user serviceable parts inside the devices.

·

Do not plug in, turn in or attempt to operate an obviously damaged device.

·

Never attempt to modify the equipment components for any reason.

Caution

!

All adjustments have been done at the factory before the shipment of the devices.
No maintenance is required and no user serviceable parts are inside the module.

Ventilation

·

Do not place the devices next to a hot source like a radiator.

·

The ventilation openings of the devices must never be blocked.

Environment

·

Never place the devices in an area of high dust particles or humidity.

·

Never place containers with any liquids on top of the devices.

·

If the devices have been exposed to a cold environment and transferred to a warm environment,
condensation may form inside the housing. Wait at least 6 hours before applying any power to the
devices.

Voltage

·

The power cable should only be connected to a correctly grounded source.

·

Do not use any adapters.

·

Never bypass a ground contact.

Danger

!

To reduce the risk of electric shock do not remove cover or expose the products 
to rain or moisture.

Warning

!

·

Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan.

·

Apparatet må tilkoples jordet stikkontakt.

·

Apparaten skall anslutas till jordat uttag.

·

Apparatets stikprop skal tilsluttes en stikkontakt med jord som giver forbindelse til
stikproppens jord.

Disposal

Disposal of old Electrical & Electric Equipment (Applicable throughout the European Union and other
European countries with separate collection programs).

This symbol, found on your product or on its packaging, indicates that this product should
not be treated as household waste when you wish to dispose of it. Instead, it should be
handed over to an applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences to the environment and human health, which could
otherwise be caused by inappropriate disposal of this product. The recycling of materials
will help to conserve natural resources. For more detailed information about the recycling
of this product please contact your local city office.

Summary of Contents for SmartPanel RSP-1232HL































Reviews: