RIDGID RP 300, Operating Instructions Manual, Page: 2 / 15

• Press the ON/OFF switch (fig.1, ref.3) to start the press fit cycle.
Important: Keep fingers and hands away from jaws during pressing
cycle!
• Wait until the complete pressing cycle has been completed.
• The tool features an automatic pressing facility. This ensures a full
pressing cycle at all times
Important: In order to ease the load of the machine in a dangerous
situation you should firmly press the yellow pressure relief button
(Fig. 1 ref. 5). The hydraulic pressure decreases, the piston retracts
and the pressure on the tool as well as the jaw will be relieved.
TROUBLESHOOTING
• If a power failure interrupts the pressing cycle, press the manual release
switch (fig. 1, ref 4) to reopen the jaws and remove the tool from the pipe.
• Whenever a pressing cycle is not fully completed, either due to a power
failure or any other cause, the complete procedure must be repeated.
-It is strongly recommended to never attempt to repeat a pressing cycle that
has been interrupted. This may lead to damage to the joint and possible
leakage. The joint should be cut out and replaced by a new one.
-The use of jaws not specifically designed and approved for pressing the
fittings being used may lead to damage and incorrectly compressed fittings.
Contact your RIDGID Press Fit Service Centre for any malfunction not covered
in this instruction manual.
MAINTENANCE
Always disconnect the tool from the power supply before performing
any maintenance.
Daily
-Clean the Press Fit tool with a soft cloth. Clean rollers and lightly lubricate.
Do not use detergents to clean the crimping tool. Check the condition of the
cable and plug daily for damage, and if damage occurs do not use the tool
and have the line cord replaced with an identical part by an authorized
service station.
Every 12 months
-The press fit tool must be sent for inspection and maintenance to the nearest
authorized RIDGID Press Fit repair centre for safety reasons.
-The repair centre will fully overhaul the tool and inspect that it is operating
correctly.
-Any unauthorized modifications and/or repairs will invalidate the warranty.
Storage
-Before storing the tool for long periods clean the tool thoroughly and wipe
clean.
-Keep away the tool from moisture and heat, and do not expose the tool to
extreme temperatures.
-Keep away from children.
-The RIDGID Press Fit tool is made of numerous metal and plastic parts.
Ensure that the tool is correctly disposed of in accordance with local
regulations.
Manual RP 300
Problem Remedy
Tool will not operate Check cable is plugged in
Tool will not operate Check power source
Tool will not operate Check that lock pin is correctly inserted
Tool will not operate Electric motor must come to complete stop
before new pressing is started
RP 300
Operating Instructions
Operating instructions
For your own safety and before using this equipment, read these
instructions and the accompanying safety booklet carefully.
If you are uncertain about any aspect of using this tool, contact your
RIDGID distributor for more information.
The RP 300 is designed for use with the majority of press fit jaws
available on the market. The tool is designed to make press fit
connections on couplings using jaws meeting the specifications of
the fitting manufacturer. The use of this tool for any other application
may damage the tool, jaws or fitting and/or cause personal injury.
Keep these instructions together with the tool
Specifications:
Model: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RP 300
Length w/out jaws: . . . . . . . . . . . . . . . . . . . . . . . . . . . .440 mm
Width: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 mm
Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 mm
Weight: (including battery): . . . . . . . . . . . . . . . . . . . . . . .5,5 kg
Technical data: . . . . . . .Class II construction 230V, 2,8A, 600W
Crimping force: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Min. 32KN
Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 – 108 mm
Operating temperature range: . . . . . . . . . . . . . . .-8°C to +50°C
Before using your RIDGID Press Fit tool:
• Check for any transport damage. Any damage should be reported
immediately to the forwarders.
• Check that all parts are included with the Press Fit tool.
• Check that the correct power cord and plug for your supply has been fitted.
• Check that the voltage on the nameplate is the same as your supply
Any repairs or Service to the RIDGID Press Fit tool must only be made
by an approved RIDGID Press Fit Service Centre.
All people involved in the working process must keep hands and fingers away
from the jaws! Unplug tool when not in use, before service or during setup or
accessory change. Avoid unintentional starting. Keep people away from
working area.
Explanation of pictograms
General warning symbol Read manual Risk of crushing
! Do not operate the tool without a pressing jaw.
The tool may be damaged.
OPERATING THE RP 300 PRESS FIT TOOL
Fitting of the jaws (see fig. 1)
• Pull out lock pin (fig. 1, ref. 1).
• Insert the correct jaw (fig.1, ref.2) (size and brand of the fitting) into the
jaw-mounting opening.
• Push in the lock pin. The tool will not start if pin is not inserted correctly.
Performing the Press Fit action
• Check that the correct jaws have been fitted for the joint that is going to be
pressed.
• Connect the tool to a power source, and place the jaws over the fitting