background image

5

SAFETY RULES FOR CHARGER

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS. 

Failure to follow all instructions listed below, may 
result in electric shock, fire and/or serious personal 
injury.

  

Before using battery charger,

 read all instructions and 

cautionary markings in this manual, on battery charger, 
battery, and product using battery to prevent misuse of 
the products and possible injury or damage.

CAUTION: 

To  reduce  the  risk  of  electric  shock  or  damage 
to  the  charger  and  battery,  charge  only  nickel-
cadmium  rechargeable  batteries  as  specifically 
designated  on  your  charger.  Other  types  of 
batteries  may  burst,  causing  personal  injury  or 
damage.

  

Do not use charger outdoors or expose to wet or damp 
conditions. 

Water entering charger will increase the risk 

of electric shock.

  

Use of an attachment not recommended or sold by the 
battery charger manufacturer may result in a risk of 
fire, electric shock, or injury to persons. 

Following this 

rule will reduce the risk of electric shock, fire, or serious 
personal injury. 

  

Do not abuse cord or charger. 

Never use the cord to 

carry the charger. Do not pull the charger cord rather than 
the plug when disconnecting from receptacle. Damage 
to the cord or charger could occur and create an electric 
shock hazard. Replace damaged cords immediately.

  

Make sure cord is located so that it will not be stepped 
on, tripped over, come in contact with sharp edges 
or moving parts or otherwise subjected to damage or 
stress. 

This will reduce the risk of accidental falls, which 

could cause injury, and damage to the cord, which could 
result in electric shock.

  

Keep cord and charger from heat to prevent damage 
to housing or internal parts.

  

Do not let gasoline, oils, petroleum-based products, 
etc. come in contact with plastic parts. 

They contain 

chemicals  that  can  damage,  weaken,  or  destroy 
plastic.

  

An  extension  cord  should  not  be  used  unless  
absolutely necessary. 

Use of improper extension cord 

could result in a risk of fire and electric shock. If extension 
cord must be used, make sure:

  a.  That pins on plug of extension cord are the same   

   number, size and shape as those of plug on charger.

  b.  That extension cord is properly wired and in  

 

   good electrical condition; and

  c.  That wire size is large enough for AC ampere  

 

   rating of charger as specified below:

 

 

     Cord Length (Feet)  

25' 

50' 

100'

       Cord Size (AWG)   

16 

16 

16

 

     

NOTE:

 AWG = American Wire Gauge

  

Do  not  operate  charger  with  a  damaged  cord  or 
plug, 

which could cause shorting and electric shock. If 

damaged, have the charger replaced by an authorized 
serviceman.

  

Do not operate charger if it has received a sharp blow, 
been  dropped,  or  otherwise  damaged  in  any  way. 

Take it to an authorized serviceman for electrical check 
to determine if the charger is in good working order. 

  

Do not disassemble charger. 

Take it to an authorized 

serviceman when service or repair is required. Incorrect 
reassembly may result in a risk of electric shock or fire.

 

 Unplug  charger  from  outlet  before  attempting  any 

maintenance or cleaning to reduce the risk of electric 
shock.

 

 

Disconnect  charger  from  the  power  supply  when 
not in use. 

This will reduce the risk of electric shock or 

damage to the charger if metal items should fall into the 
opening. It also will help prevent damage to the charger 
during a power surge.

 

Risk of electric shock. 

Do not touch uninsulated portion 

of output connector or uninsulated battery terminal.

  

Save these instructions. 

Refer to them frequently and 

use them to instruct others who may use this tool. If you 
loan someone this tool, loan them these instructions also 
to prevent misuse of the product and possible injury.

IMPORTANT SAFETY INSTRUCTIONS

1.

 

SAVE THESE INSTRUCTIONS

 

This manual contains important safety and operating instructions for battery charger

 

140276003.

2.

 

Before using battery charger,

 read all instructions and cautionary markings on battery charger, battery, and product 

using battery.

3.

 

CAUTION:

 

To reduce the risk of injury, charge only nickel-cadmium rechargeable batteries. Other types of batteries 

may burst, causing personal injury or damage.

Summary of Contents for R8433





















Reviews: