background image

11

30

min

30

min

?

OPERATION

LED

BATTERY

RED

GREEN

ACTION

INDICATOR

PACK

LED

LED

Power

Without battery pack

ON

OFF

Ready to charge battery pack

Evaluate

Hot battery pack

Flashing

OFF

When battery pack reaches
cooled temperature, charger
begins fast charge mode

Evaluate

Cold battery pack

Flashing

OFF

When battery pack reaches
warmed temperature, charger
begins fast charge mode

Evaluate

Deeply discharged

Flashing

OFF

Charger pre-charges battery
until normal voltage is reached,
then begins fast charge mode

Evaluate

Thermistor shorted

Flashing

OFF

If red LED continues flashing for

or open

more than 90 minutes, and
green LED remains off, this may
indicate a damaged battery

Charging

Fast charging

ON

Flashing

Fast charges in 30 minutes

Full

Slow charging

OFF

ON

Fast charging is complete.
Charger maintains charge mode.

LED FUNCTION OF CHARGER

See Figure 3.

Fig. 3

POWER

INDICATOR

EVALUATE

INDICATOR

CHARGING

INDICATOR

FULL

INDICATOR

Charging

Cargando

En charge

Full

Completo

Charge max.

?

Evaluate

Evaluer

Evaluar

Power

Corriente

Alimentation

Summary of Contents for R841150























Reviews: