background image

11

OPERATION

LED FUNCTION OF CHARGER

See Figure 3.

Fig. 3

POWER

INDICATOR

EVALUATE

INDICATOR

DEFECTIVE

INDICATOR

FULL

INDICATOR

LED

INDICATOR

BATTERY 

PACK

RED

LED

GREEN

LED

ACTION

Power

Without battery pack ON

OFF

Ready to charge battery pack

Evaluate

Hot battery pack

Flashing

OFF

When  battery  pack  reaches  cooled 
temperature,  charger  begins  fast 
charge mode

Evaluate

Cold battery pack

Flashing

OFF

When battery pack reaches warmed 
temperature,  charger  begins  fast 
charge mode

Evaluate

Deeply discharged

Flashing

OFF

Charger pre-charges battery until nor-
mal voltage is reached, then begins 
fast charge mode

Defective

Defective

Flashing

Flashing

Battery pack or charger is defective.

•  If defective, try to repeat the conditions a second time by removing and reinstalling the battery 

pack. If the LED status repeats a second time, try charging a different battery.

•  If a different battery charges normally, dispose of the defective pack (see Maintenance section).
•  If a different battery also indicates “Defective,” the charger may be defective.

Charging

Fast charging

ON

Flashing

See chart below for charge times

Full

Slow charging

OFF

ON

Fast charging is complete.
Charger maintains charge mode.

BATTERY

AVERAGE CHARGE TIME

COMPACT SERIES

18 min.

HC

27 min.

HC 2.5

34 min.

NOTE: 

The 9.6 Volt, 12 Volt, and 14.4 Volt battery 

packs will not slide all the way down onto the char-
ger port. Insert 9.6 Volt, 12 Volt, and 14.4 Volt battery 
packs until they click into place and are aligned with 
the line on the charger, shown at left. 
Allow up to 5 seconds for the “charge” light to come 
on after the battery pack is inserted.

GREEN LED

RED LED

CHARGING

INDICATOR

Summary of Contents for R830153





















Reviews: