background image

16

MAINTENANCE

WARNING:

 

 

When  servicing  use  only  identical  RIDGID 
replacement  parts.  Use  of  any  other  parts  may 
create a hazard or cause product damage.

WARNING:

Always wear safety goggles or safety glasses with 
side shields during power tool operation or when 
blowing  dust.  If  operation  is  dusty,  also  wear  a 
dust mask.

WARNING:

To  avoid  serious  personal  injury,  always  remove 
the battery pack from the tool when cleaning or 
performing any maintenance.

GENERAL MAINTENANCE

Avoid  using  solvents  when  cleaning  plastic  parts.  Most 
plastics are susceptible to damage from various types of 
commercial solvents and may be damaged by their use. Use 
clean cloths to remove dirt, dust, oil, grease, etc.

WARNING: 

Do  not  at  any  time  let  brake  fluids,  gasoline, 
petroleum-based products, penetrating oils, etc., 
come in contact with plastic parts. Chemicals can 
damage,  weaken  or  destroy  plastic  which  may 
result in serious personal injury.

Only the parts shown on the parts list are intended to be  
repaired or replaced by the customer. All other parts should 
be replaced at a RIDGID authorized service center.

BATTERIES

The battery pack for this tool is equipped with nickel-cad-
mium rechargeable batteries. Length of service from each 
charging will depend on the type of work you are doing.
The batteries in this tool have been designed to provide 
maximum trouble-free life. However, like all batteries, they 
will eventually wear out. 

Do not 

disassemble battery pack 

and attempt to replace the batteries. Handling of these 
batteries, especially when wearing rings and jewelry, could 
result in a serious burn.
To obtain the longest possible battery life, we suggest the 
following:

  Remove the battery pack from the charger once it is fully 

charged and ready for use.

For battery pack storage longer than 30 days:

  Store the battery pack where the temperature is below 

80°F. 

  Store battery packs in a “discharged” condition.

BATTERY PACK REMOVAL AND PREPARATION 
FOR RECYCLING

To preserve natural resources, please 
recycle  or  dispose  of  batteries 
properly.
This product contains nickel-cadmium 
batteries.  Local,  state  or  federal 
laws may prohibit disposal of nickel-
cadmium batteries in ordinary trash.

Consult your local waste authority for information regarding 
available recycling and/or disposal options. 

WARNING:

Upon removal, cover the battery pack’s terminals 
with  heavy-duty  adhesive  tape.  Do  not  attempt 
to  destroy  or  disassemble  battery  pack  or 
remove any of its components. Nickel-cadmium 
batteries must be recycled or disposed of properly. 
Also, never touch both terminals with metal objects 
and/or body parts as short circuit may result. Keep 
away from children. Failure to comply with these 
warnings could result in fire and/or serious injury.

Summary of Contents for R820011





















Reviews: