4
GENERAL SAFETY RULES
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal
sparking of the motor could ignite fumes.
INSPECT TOOL CORDS PERIODICALLY.
If damaged,
have repaired by a qualified service technician at an
authorized service facility. The conductor with insulation
having an outer surface that is green with or without yellow
stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to a
live terminal. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating blade.
INSPECT EXTENSION CORDS PERIODICALLY
and
replace if damaged.
POLARIZED PLUGS.
To reduce the risk of electric shock,
this tool has a polarized plug (one blade is wider than
the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install the proper outlet. Do not change the plug in any
way.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE.
Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
STAY ALERT AND EXERCISE CONTROL.
Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF.
Have defective switches replaced by an
authorized service center.
USE ONLY CORRECT BLADES. Do not
use blades with
incorrect size holes. Never use blade washers or blade
bolts that are defective or incorrect. The maximum blade
capacity of the saw is 12 in.
BEFORE MAKING A CUT, BE SURE ALL ADJUST-
MENTS ARE SECURE.
BE SURE BLADE PATH IS FREE OF NAILS.
Inspect for
and remove all nails from lumber before cutting.
NEVER TOUCH BLADE
or other moving parts during
use.
NEVER START A TOOL WHEN ANY ROTATING
COMPONENT IS IN CONTACT WITH THE WORKPIECE.
DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
WHEN SERVICING
use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
USE ONLY RECOMMENDED ACCESSORIES
listed
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included
with the accessory.
DOUBLE CHECK ALL SETUPS.
Make sure blade is
tight and not making contact with saw or workpiece
before connecting to power supply.
SPECIFIC SAFETY RULES
FIRMLY CLAMP OR BOLT
the tool to a workbench or
table at approximately hip height.
KEEP HANDS AWAY FROM CUTTING AREA.
Do not
reach underneath work or in blade cutting path with your
hands and fingers for any reason. Always turn the power off.
ALWAYS SUPPORT LONG WORKPIECES
while cutting
to minimize risk of blade pinching and kickback. Saw may
slip, walk, or slide while cutting long or heavy boards.
ALWAYS USE A CLAMP
to secure the workpiece when
possible.
BE SURE THE BLADE CLEARS THE WORKPIECE.
Never
start the saw with the blade touching the workpiece. Allow
motor to come up to full speed before starting cut.
MAKE SURE THE MITER TABLE AND SAW ARM BEVEL
FUNCTION) ARE LOCKED IN POSITION BEFORE
OPERATING YOUR SAW.
Lock the miter table by securely
tightening the miter lock lever. Lock the saw arm (bevel
function) by securely tightening the bevel lock lever.
USE THIS SAW TO CUT WOOD, WOOD PRODUCTS,
AND SOME PLASTICS ONLY. DO NOT CUT METALS,
CERAMICS OR MASONRY PRODUCTS.
BEFORE MOVING THE SAW,
unplug the saw then lock
the miter, bevel, slide, and power head positions.
NEVER USE A LENGTH STOP ON THE FREE SCRAP
END OF A CLAMPED WORKPIECE. NEVER
hold onto
or bind the free scrap end of the workpiece in any opera-
tion. If a work clamp and length stop are used together,
they must both be installed on the same side of the saw
table to prevent the saw from catching the loose end and
kicking up.
NEVER
cut more than one piece at a time.
DO NOT
STACK
more than one workpiece on the saw table at a
time.
NEVER PERFORM ANY OPERATION FREEHAND.
Always place the workpiece to be cut on the miter table
and position it firmly against the fence as a backstop.
Always use the fence.
