Ride1up Roadster V2 Owner'S Manual Download Page 11

Page: 11 / 16

For the most up to date documents, bike models, additional information, instructional videos,

and more visit us at

Ride1UP.com

3.6 Spoke Tension:

4. Charging the Battery

WARNING

◆

DO NOT LEAVE CHARGING BATTERY UNATTENDED

Your battery must be charged in an ambient temperature, on a non-flammable & dry surface, away from

any sources of heat, humidity or flammable materials. Also, it must not be covered.

If you ever see a spark while charging your battery. Please inspect the charging port of the battery and

the tip of the charger. Please contact

[email protected]

and share pictures.

Follow these steps when charging battery:

Step 1.

Turn the bike off. The LCD will be off.

Step 2.

Plug the charger (which is off) into the wall socket and then insert

the chargers plug into the charging port on the bike. When opening the

charger port cover, Rotate it. DO NOT PULL OUTWARD.

Make sure the charger’s tip is not stressed or supporting the weight of the
charger. Do not wiggle the charger’s tip in the charging port of the battery.

NOTE:

ALWAYS KEEP THE CHARGER PORT CLOSED WHEN NOT CHARGING. Failure to do so

may permanently damage your battery.

Step 3.

The chargers LED indicators light up in the following manner:

Summary of Contents for Roadster V2

















Search results

Summary of Contents for Roadster V2

Reviews:

Related manuals for Roadster V2

Brands by name

Popular brands

Ride1up Roadster V2, Owner'S Manual

Search results

Summary of Contents for Roadster V2

Reviews:

Related manuals for Roadster V2

Brands by name

Popular brands