Ricoh SR4110 Field Service Manual Download

Page: 21 / 60

1.Detailed Descriptions

Stapling

Stapler

The drive motor in the stapler performs stapling. If motor overload occurs such as for a staple jam, the operation

panel shows that a jam was detected. The stapler has a cartridge set sensor and a staple end sensor. The operation

panel shows that more staples are needed if staple end occurs during copying. If a staple jam occurs, copying

stops. You can remove a jammed staple by releasing the curved part in the picture below..

No.

Description

No.

Description

Staple Cartridge Set Sensor

Staple End Sensor

Staple Trimming

This machine’s stapler uses longer staple needles so that up to a hundred sheets can be stapled. When the stack has

only a few sheets, the machine trims the needles to the required length. The cut-off extra part is sent to the staple

trimmings tray.

When the main power is turned ON,

when the door is opened/closed, or

after the end of a

job that staples over 100 times, the solenoid next to the stapler opens the lever to dump the trimmings into the

waste hopper. The staple trimmings hopper descends as it fills, until the staple trimmings hopper full sensor is

activated. A message asks the user to empty the staple trimmings.

Summary of Contents for SR4110





























































Search results

Summary of Contents for SR4110

Reviews:

Related manuals for SR4110

Brands by name

Popular brands

Ricoh SR4110, Field Service Manual

Search results

Summary of Contents for SR4110

Reviews:

Related manuals for SR4110

Brands by name

Popular brands