Ricoh Aficio IS 2425 Operating Instructions Manual Download Page 47 | Manualshive

Page: 47 / 288

background image

39

2. System Settings

This chapter describes user tools in the System Settings menu. For details on
how to access System Settings, see "Accessing User tools (System Settings)".

General Features

This section describes the user tools in the General Features menu under System
Settings.
Default settings are shown in

bold type

.

❖

Panel Tone

The beeper (key tone) sounds when a key is pressed.
The default setting is

On

.

❖

Warm Up Notice (copier/Document Server)

You can have the beeper sound when the machine becomes ready to copy af-
ter leaving Energy Saver mode, or when the power is turned on.
The default setting is

On

.

❖

Copy Count Display (copier/Document Server)

The copy counter can be set to show the number of copies made (count up) or
the number of copies yet to be made (count down).
The default setting is

Up (count up)

.

❖

Function Priority

Specify the mode to be displayed immediately after the operation switch is
turned on, or when System Reset mode is turned on.
The default setting is

Copier

.

❖

Print Priority

Print Priority is given to the mode selected.
When

[

Interleave

]

is selected, the current print job will be interrupted after a

maximum of five sheets.
The default setting is

Display Mode

.

When

[

Interleave

]

is selected, the current print job will be interrupted after a

maximum of five sheets.
When the Internal Tray 2 (1 bin tray), Shift Sort Tray, 500–sheet finisher, or
1000–sheet finisher is installed on the machine, you can specify an output tray
for each documents are delivered. For details about how to specify an output
tray for each function, see "Output: coier", "Output: Document Server", "Out-
put: Facsimile", "Output: Printer".

«
...
45
46
47
48
49
...
»

Summary of Contents for Aficio IS 2425

































































































































































































































































































Reviews:

No comments

Related manuals for Aficio IS 2425

Panafax UF-7000

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 120

Brand: Panasonic Pages: 100

KX-MB781 - B/W Laser - All-in-One

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 130

Brand: Oki Pages: 210

Brand: Panasonic Pages: 77

Brand: Panasonic Pages: 402

Brand: Panasonic Pages: 54

Workio DP-8016P

Brand: Panasonic Pages: 88

Brand: Panasonic Pages: 60

Brand: ABLE Pages: 26

Brand: TE Connectivity Pages: 2

Brand: TE Connectivity Pages: 2

Brand: Oki Pages: 1

imageRUNNER 5075

Brand: Canon Pages: 502

imageRUNNER 5075

Brand: Cannon Pages: 268

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands