Richtek RT8239A Manual Download Page 1

RT8239A/B/C

®

DS8239A/B/C-06   October  2012

www.richtek.com

1

Copyright   2012 Richtek Technology Corporation. All rights reserved.                          is a registered trademark of Richtek Technology Corporation.

©

Ordering Information

Note :
Richtek products are :

`

 RoHS compliant and compatible with the current require-

  ments of IPC/JEDEC J-STD-020.

`

 Suitable for use in SnPb or Pb-free soldering processes.

High Efficiency, Main Power Supply Controller
for Notebook Computers

General Description

The RT8239A/B/C is a dual step down, Switch Mode Power
Supply (SMPS) controller which generates logic supply
voltages for battery powered systems. It includes two
Pulse Width Modulation (PWM) controllers adjustable
from 2V to 5.5V and also two fixed 5V/3.3V linear
regulators. One of the controllers (LDO5) provides
automatic switch over to the BYP1 input connected to
the main SMPS1 output for maximized efficiency. An
optional external charge pump can be monitored through
SECFB (RT8239B/C). Other  features include on board
power up sequencing, a power good output, internal soft-
start, and a soft discharge output that prevents negative
voltage during shutdown.

A constant on-time PWM control scheme operates without
sense resistors and assures fast load transient response
while maintaining nearly constant switching frequency. To
eliminate noise in audio applications, an ultrasonic mode
is included, which maintains the switching frequency
above 25kHz. Moreover, a diode emulation mode
maximizes efficiency for light load applications. The
SMPS1/SMPS2 switching frequency can be adjustable
from 200kHz/233kHz to 400kHz/466kHz respectively.

The RT8239A/B/C is available in a WQFN-20L 3x3
package, and operates over an extended temperature range
from 

40

°

C to 85

°

C.

Features

z

z

z

z

z

5.5V to 25V Input Voltage Range

z

z

z

z

z

2V to 5.5V Output Voltage Range

z

z

z

z

z

No Current Sense Resistor Needed

z

z

z

z

z

5V/3.3V Linear Regulators

z

z

z

z

z

4700ppm/

°°°°°

C R

DS(ON)

 Current Sensing

z

z

z

z

z

Internal Current Limit Soft-Start and Soft Discharge

Output

z

z

z

z

z

Built In OVP/UVP/OCP

z

z

z

z

z

Selectable Operation Mode with Switcher Enable

Control (RT8239A)

z

z

z

z

z

SECFB Input Maintains Charge Pump Voltage

(RT8239B/C)

z

z

z

z

z

Power Good Indicator (RT8239B/C includes SECFB)

z

z

z

z

z

RoHS Compliant and Halogen Free

Applications

z

Notebook computers

z

System Power Supplies

z

3- and 4- Cell Li+ Battery-Powered Device

RT8239A/B/C

Package Type
QW : WQFN-20L 3x3 (W-Type)
Lead Plating System
G : Green (Halogen Free and Pb Free)
Z : ECO (Ecological Element with   
      Halogen Free and Pb free)
Pin Function With
A : ENM
B : SECFB
C : SECFB, Ultrasonic Mode

Summary of Contents for RT8239A

























Reviews: