Rice Lake Benchmark LP Installation Manual Download Page 13

9

Benchmark LP Limited Warranty

Rice Lake Weighing Systems (RLWS) warrants that all RLWS equipment and systems properly installed by a 
Distributor or Original Equipment Manufacturer (OEM) will operate per written specifications as confirmed by 
the Distributor/OEM and accepted by RLWS. All systems and components are warranted against defects in 
materials and workmanship for two years. 
RLWS warrants that the equipment sold hereunder will conform to the current written specifications authorized 
by RLWS. RLWS warrants the equipment against faulty workmanship and defective materials. If any equipment 
fails to conform to these warranties, RLWS will, at its option, repair or replace such goods returned within the 
warranty period subject to the following conditions:|

 

Upon discovery by Buyer of such nonconformity, RLWS will be given prompt written notice with a 

detailed explanation of the alleged deficiencies.

Individual electronic components returned to RLWS for warranty purposes must be packaged to prevent 

electrostatic discharge (ESD) damage in shipment. Packaging requirements are listed in a publication, 

“Protecting Your Components From Static Damage in Shipment,” available from RLWS Equipment 

Return Department.

Examination of such equipment by RLWS confirms that the nonconformity actually exists, and was not 

caused by accident, misuse, neglect, alteration, improper installation, improper repair or improper 

testing; RLWS shall be the sole judge of all alleged non-conformities.

Such equipment has not been modified, altered, or changed by any person other than RLWS or its duly 

authorized repair agents.

RLWS will have a reasonable time to repair or replace the defective equipment. Buyer is responsible for 

shipping charges both ways.

In no event will RLWS be responsible for travel time or on-location repairs, including assembly or 

disassembly of equipment, nor will RLWS be liable for the cost of any repairs made by others.

THESE WARRANTIES EXCLUDE ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, 

INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY OR FITNESS 

FOR A PARTICULAR PURPOSE. NEITHER RLWS NOR DISTRIBUTOR WILL, IN ANY EVENT, 

BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. 

RLWS AND BUYER AGREE THAT RLWS’ SOLE AND EXCLUSIVE LIABILITY HEREUNDER IS 

LIMITED TO REPAIR OR REPLACEMENT OF SUCH GOODS. IN ACCEPTING THIS WAR-

RANTY, THE BUYER WAIVES ANY AND ALL OTHER CLAIMS TO WARRANTY.

SHOULD THE SELLER BE OTHER THAN RLWS, THE BUYER AGREES TO LOOK ONLY TO 

THE SELLER FOR WARRANTY CLAIMS.

No terms, conditions, understanding, or agreements purporting to modify the terms of this warranty shall have any legal effect 
unless made in writing and signed by a corporate officer of RLWS and the Buyer.

© 2008 Rice Lake Weighing Systems, Inc. Rice Lake, WI USA.  All Rights Reserved.

RICE LAKE WEIGHING SYSTEMS  

• 

230 WEST COLEMAN STREET  

• 

RICE LAKE, WISCONSIN 54868  

 USA

Summary of Contents for Benchmark LP














Reviews: