Ribimex Ribitech PE12V/2500 User And Maintenance Manual Download Page 17

14. Attention: do not overreach and stay alert 

- Keep proper footing and balance at all times 
- Pay attention to what you are doing and use your common sense  
- Do not operate the product when you are tired, while under the influence of alcohol, 
prescription medicines or drugs. 
Read warning labels of prescriptions to determine whether your judgment or reflexes would be 
impaired while taking drugs. If there is any doubt, do not operate the tool. 
- Do not reach over or across running machines 

15. Important 

- The user and/or operator are responsible for any damages or injury caused to properties and 
persons. 

16. Store idle equipment 

- When not in use, product must be locked up in a dry location. Always lock up product and keep 
out of reach of children 

17. Remove adjusting keys and wrenches. 

- Be sure that keys and adjusting wrenches are removed from the product before operation  

18. Check for damaged parts.  

- Before using or re-using the product, carefully check for all parts, to determine if product will 
operate properly and perform its intended function. Components may be affected by exposure to 
chemicals, salts, and rust. 
- Check for alignment and binding of moving parts, any broken parts or mounting fixtures, and 
any other condition that may affect proper operation.  
- Regularly check the steel cable for signs of tear and wear. Replace any damaged cable at an 
authorized service centre. 
- Unless otherwise stated in the instructions, any part that is damaged should be properly 
repaired or replaced by a qualified technician.  
- Do not use the product if the remote control does not turn on and off properly. Repair or replace 
it at an authorized service centre. 

19. Accessories.  

- The use of any accessories, other than those recommended by the manufacturer or stated in the 
instructions manual, may result in injury or may cause damages. 

20. Remark: 

- The safety precautions and instructions given in this manual are unable to cover in detail all the 
conditions and situations that may arise.  
- The operator and/or user must use common sense and caution when operating the product 
especially for any matters that are not referred in the above. 

 

3.3- Special warnings when using the electric winch 

1. Become familiar with the controls and proper use of the product. 
2. Only well-instructed adults should operate the product. 
This product is not intended for use by persons (including children) with reduced physical, sensory or 
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 
instruction concerning use of the appliance by a person responsible for their safety 
3. Never connect a hook to the wire steel cable. This could damage the cable.  
Always use proper couplings when connecting winch cable hook to load i.e. use a sling or chain of a 
suitable strength. 
4. There is no problem if the cable is rewound unevenly while pulling a load, unless there is a 
pile-up of the cable at one end of the drum. If such pile-up happens, reverse the winch to relieve the 
load and move the anchor point further to the centre of the vehicle.  
5. When the job is done, we recommend unwinding the cable and then rewinding it neatly. 
6. Store the remote control inside the vehicle where it will not be damaged and inspect it before 
use. 

Summary of Contents for Ribitech PE12V/2500


































Reviews: