RIB VERTIGO WIRELESS 10, Manual

Page: 16 / 28

16
16
G
B
16
16
S
YSTEM CHECK
After finishing the mounting procedure, check the correct working order by doing the
following:
-
Check on the infrared receiver RX VERTIGO WIRELESS that the red led is on. If it is not so,
align transmitter and receiver to turn the red led on.
- Place an object between them and check that the red LED turns OFF and that at the same
time on the control panel the corresponding LED EDGE is OFF and a while the object is
present.
- Repeat the process on the other VERTIGO WIRELESS photocells installed.
- Then perform a system check of all the photocells installed by activating the movement of
the automation and checking that when an object is present the automation stops/reverses
when closing, or stops/continues to open when opening.
C
LOSING THE VERTIGO WIRELESS CONTAINERS
Lastly, place the screw cover caps (6) (12) both on the TX and on the RX of the VERTIGO
WIRELESS (Fig. 2-5), by inserting them into the 4 holes so that they are perfectly attached.
C
HANGING THE BATTERIES
The duration of the batteries used for VERTIGO WIRELESS photocells is about 2 years.
- To identify which VERTIGO transmitter has empty batteries, it is enough to check the red
led present on the receiver. It should be turned off in presence of no obstacles between
transmitter and receiver.
- Replace the batteries of the transmitter checking that the polarity is correct.
The automation is now ready to begin safe operation once more.
ATTENTION: Please remember that batteries must be disposed of properly
according to current standards. In case of disposal of the photocells please
remember to remove and dispose of the batteries properly.
T
ECHNICAL SPECIFICATIONS
VERTIGO WIRELESS RECEIVER
- POWER 12/24V ac/dc
- MAXIMUM ABSORPTION 25 mA
- OPERATING TEMPERATURE -20°C ÷ +60°C
- COVER in polycarbonate
- BASE in ABS
- BELLOW in silicon
- PROTECTION LEVEL IP55
- WEIGHT 0,135 kg
VERTIGO WIRELESS TRANSMITTER
- POWER alkaline batteries 2 x AA 1,5V (>2,7Ah)
- POWER ABSORBED 3 µA
- MODULATION TYPE FSK
- BATTERY LIFE about 3 years
- OPERATING TEMPERATURE -20°C ÷ +60°C
- COVER in polycarbonate
- BASE in ABS
- BELLOW in silicon
- PROTECTION LEVEL IP55
- WEIGHT 0,130 kg
TX INFRARED SIGNAL TECHNICAL DETAILS
- RANGE 3 m
- WAVELENGTH 850 nm
- DIMENSION OF THE DETECTION AREA Ø 20 mm
A
PPLICATION
MAX GATE
WEIGHT
MAX DISPLACEMENT
SPEED
VERTIGO WIRELESS 8
150 kg
300 kg 13 m/min.
10 m/min.
VERTIGO WIRELESS 10
500 kg
1000 kg
13 m/min.
10 m/min.
T
ROUBLESHOOTING
PROBLEM CHECK
The green LED DLTX of the TX does not turns on as you give power supply. - Check batteries onTX.
The red LED DLRX of the RX does not turns on as you give power supply. - Check that on RX terminals is present the power supply 12/24V ac/dc
- Check batteries onTX.
- Check the correct allignment between TX and RX
The gate does not open. VERTIGO WIRELESS is not aligned or stuck (red led on RX turned OFF). Check alignment
between TX and RX up to obtain red led turned on on RX.
The gate does not close. AUTOTEST failed.
VERTIGO WIRELESS is not aligned or stuck (red led on RX turned OFF). Check alignment
between TX and RX up to obtain red led turned on on RX.
SELF-TEST-ENABLED RIB ELECTRONIC BOARD CHART
RIB ELECTRONIC BOARD CONNECT A/D+ TEST
TERMINAL TO TERMINAL ENABLE SELF-TEST
FUNCTION THROUGH
K2007 / K2007 CRX A+ TEST DIP 10
S1 A+ TEST DIP 12
T2 - T2 CRX D+ TEST DIP 13
T2 24V - T2 24V CRX A+ TEST DIP 12
OPTIONAL
AA ALKALINE BATTERIES
4 X 1,5V
battery life with VERTIGO WIRELESS 2 years.
code ACG9519
AA LITHIO BATTERIES
2 X 1,5V - (buy 2 pieces)
battery life with VERTIGO WIRELESS 3 years.
For extreme temperatures -40÷+60°C.
code ACG9509