manualshive.com logo in svg

Rhodan HD GPS ANCHOR+, Owner'S Manual

Share
Download
Rhodan HD GPS ANCHOR+ Owner'S Manual Download Page 21

w w w . r h o d a n m a r i n e . c o m

CUSTOMER SERVICE: 1-888-434-7726

21

APPENDIX G:

FOB FEATURES

REPLACING A FOB BATTERY

1.  Using a #1 phillips screwdriver, remove the two screws on the back of the fob.
2.  Separate the fob sections
3.  Remove the rubber membrane and the circuit board from the back half of the fob shell.
4.  Slide the battery out of its holder on the back of the circuit board and replace with 

a new CR2032 battery.  Be sure to position the battery with the Positive side away 

from the board.

5.  Reinstall the circuit board in the back half of the fob shell, taking care to make 

sure it is properly positioned in the shell.
6.  Place the rubber membrane over the lip on the back half of the fob shell and press into place.
7.  Place the front half of the fob shell over the rubber membrane and press into 

place.  Verify that all buttons are properly positioned within their opening and func-

tion correctly.
8.  Reinstall the two screws into the fob shell, taking care not to over-tighten the screws.  

PROGRAMMING A NEW WIRELESS CONTROL FOB

1.  Power up the unit in the stowed position
2.  Deploy, stow and re-deploy the unit prior to pressing any fob buttons.
3.  The unit will begin “beeping” indicating that it is ready to learn new wireless controls.
4.  Press any button on the new fob within 20 seconds
5.  When the unit stops beeping, the new fob will be learned by your system and is 

ready to be used.

Use care not to press the small switch on the back of the circuit board near 
the battery holder.  If this switch is accidentally pressed, or the unit does not 

respond to fob commands after replacing a battery, please contact Rhodan Marine 
Systems for further assistance.

The batteries in the wireless FOB should be capable of lasting a full fishing 
season or longer under normal usage conditions.  If your system is powered 
up yet fails to respond to a FOB, or if you noticed decreased wireless range, 

try replacing the battery.”

Warning, do not attempt to stow the unit 
until it has stopped beeping.

Summary of Contents for HD GPS ANCHOR+

























Reviews:

No comments

Brands by name

Popular brands

Load more brands