background image

F-3778-12-04

Safety Section 1-3

© 2004

Alamo Group Inc.

Si no lee Ingles, pida ayuda a alguien que si Io

lea para que Ie traduzca las medidas de

seguridad.

Never operate the Power Unit or Implement until you have read

and completely understand this Manual, the Power Unit Operator’s

Manual, and each of the Safety Messages found in the Manual or

on the Power Unit and Implement. Learn how to stop the Power

Unit engine suddenly in an emergency. Never allow inexperienced

or untrained personnel too operate the Power Unit and Implement

without supervision. Make sure the operator has fully read and

understood the manuals prior to operation.

Always maintain the safety decals in good readable condition. If

the decals are missing, damaged, or unreadable, obtain and install

replacement decals immediately.

Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be clearly

visible and legible. When transporting the Equipment use the Power Unit flashing warning lights and

follow all local traffic regulations.

Operate this Equipment only with a Tractor equipped with an

approved roll-over-protective system (ROPS). Always wear seat

belts. Serious injury or even death could result from falling off the

tractor—particularly during a turnover when the operator could be

pinned under the Operator Protective Structure.

Do not modify or alter this Implement. Do not permit anyone to

modify or alter this Implement, any of its components or any

Implement function.

BEFORE leaving the Power Unit seat, always engage the brake and/or set the Power Unit

transmission in parking gear, disengage the auxiliary hydraulics, stop the engine, remove the key, and

wait for all moving parts to stop. Place the Power Unit shift lever into a low range or parking gear to

prevent the tractor from rolling. Never dismount a Power Unit that is moving or while the engine is

running. Operate the Power Unit controls from the operator seat only.

SAFETY

SAFETY

DANGER!

PELIGRO!

WARNING!

WARNING!

WARNING!

WARNING!

DANGER!

Summary of Contents for RHINO 7214 MSL













































Reviews:

Related manuals for RHINO 7214 MSL