Rhin-O-Tuff APES-14 HD-6500 Operator'S Manual Download Page 20 | Manualshive

Page: 20 / 21

background image

9) HD-6500 and HD-7000 Removing Punch Pins:
Make sure the machine is turned off before removing the die. To remove a punch pin
from the die, disengage both quick change die handles and slide the die to the right until
the die is completely removed from punch.

Step 1. Remove top pin retainer by pushing down first, and then
pulling away from bottom pin retainer to expose punch pins.

Step 2. Remove desired punch pin.

Step 3. Place edge of top pin retainer along punch pins and press
down while pulling pin retainer back to original position.

Step 4. Install die into machine as described in previous section.

Page 18

Issue “A1” 09/03 PDI Part # 900600 www.RHIN-O-TUFF.com

«
...
18
19
20
21
»

Summary of Contents for APES-14 HD-6500






















Reviews:

No comments

Related manuals for APES-14 HD-6500

Brand: Janome Pages: 80

Brand: Singer Pages: 74

Brand: NSS Pages: 12

ST1000E with TRS

Brand: Sure Sweep Pages: 36

Brand: Singer Pages: 7

Brand: KISANKRAFT Pages: 14

Brand: Garudan Pages: 80

Brand: Racing Pages: 3

Brand: TAJIMA Pages: 118

Brand: Singer Pages: 67

Brand: Baby Lock Pages: 69

Brand: Beko Pages: 40

Brand: Beko Pages: 36

Brand: JUKI Pages: 88

Brand: Nobles Pages: 1

Brand: JUKI Pages: 62

Brand: Stern Pinball Pages: 52

Brand: Kettler Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands