Rheem Solar Premier Loline 596270 Page 39 Owner'S Manual And Installation Instructions Download | Manualshive

Page: 39 / 68

background image

39

STORAGE TANK AND GAS BOOSTER ASSEMBLY

GAS BOOSTER BRACKETS

– 874826 MODELS

INSTALLER PLEASE NOTE:

It is necessary to replace the top mounting bracket with the bracket supplied with the solar storage tank and
relocate the bottom mounting bracket on an 874826 gas booster water heater when mounting it on the 596270
model solar tank.

Replacing the Top Mounting Bracket

To replace the top bracket:

1.

Remove the top mounting bracket from the gas
booster water heater by removing the two
screws. Put the screws aside.

The bracket can be discarded.

2.

Position the new mounting bracket supplied
over the two central holes and fit using the
screws removed in step 1.

Note the correct orientation of the bracket in the
image below. Tighten the screws.

«
...
37
38
39
40
41
...
»

Summary of Contents for Solar Premier Loline 596270





































































Reviews:

No comments

Related manuals for Solar Premier Loline 596270

Brand: Calcana Pages: 96

Brand: Gardena Pages: 8

Brand: Laser Pages: 4

FireSense Bessemer Patio Fireplace

Brand: Balkene Home Pages: 10

Brand: Westinghouse Pages: 12

Brand: Barracuda PUMPS Pages: 4

Pond Clear 5000

Brand: SuperFish Pages: 12

Brand: salmson Pages: 68

Brand: CLAS Pages: 20

SMART GEYSER 2330-03

Brand: Simer Pages: 12

Brand: Burley Pages: 22

LNVx CCF Series

Brand: Powrmatic Pages: 48

Brand: Xylem Pages: 54

Brand: Xylem Pages: 36

Brand: Wacker Neuson Pages: 42

Brand: T.I.P. Pages: 134

HEATSTAR MH35CLP

Brand: Mr. Heater Pages: 32

Brand: KABI Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands