manualshive.com logo in svg

Rheem RXRD-NDCM3, Installation Instructions Manual, Page: 11 / 12

Share
Download
Rheem RXRD-NDCM3 Installation Instructions Manual Download Page 11

Hor i zon tal  Mod u lat ing  Gear  Economizer

RKKB / RLKB 090-240

Notes:
1.  Unit wir ing shown as ref er ence only.  Check unit wir ing for ac tual unit wir ing.
2.

Re lays 1K and 2K ac tu ate when the Out door Air Enthalpy is lower than the Re turn Air Enthalpy.

3.

1S is an elec tronic switch which closes when pow ered by a 24 VAC in put.

4.

Fac tory in stalled re sis tor should be re moved only if C7400 Dif fer en tial Enthalpy Sen sor is added.

5.

Y2 must be en er gized for the com pres sor to op er ate.

WIRE COLOR CODE

BLK

Black

BLU

Blue

BRN

Brown

GRN Green

GRY

Gray

ORG Orange

RED

Red

TAN

Tan

VIO

Violet

WHT White

YEL

Yellow

COMPONENT CODE

9RT1H

Mixed Air Sensor

C7400A

Fresh Air Sensor

J2

Power Exhaust Cap

MS7106K 

Damper Actuator 24v

PL6

Male A/C Unit Plug

PL7

Female Economizer Cap

W7213A

Logic Module

Re vi sion

Change

Date

A

Changed Mixed Air Sensor

02-23-06

B

Ex changed wire 3 & 4

03-29-06

C

Switched wires 3 & 4 on PL7

01-04-08

D

ECN# 5938

08-18-11

E

ECN# 6467

05-01-13

HARNESS ENDS AT PL7

CONNECTOR & CONTACT CONFIGURATION

PL7 (300000297) CAP - (300000558) SOCKET

J2 (300000291) CAP - (300000558) SOCKET

Date: May 1, 2013

Supersedes: 08-18-11

Drawn by: MGL

Unit #: 60-394-13/15

Di a gram#:  6039413W

Ap proved  by:

Summary of Contents for RXRD-NDCM3













Reviews:

No comments