Rheem RPVE Series Installation, Operation & Maintenance Instructions Manual Download Page 4

R e s i d e n t i a l   S p l i t

R e v. :   1 3   M a r c h ,   2 0 1 5

4

 

WARNING! 

 

WARNING! 

 

CAUTION! 

Safety

CAUTION! 

To avoid equipment damage, DO NOT use 

these units as a source of heating or cooling during the 
construction process. The mechanical components and 
fi lters will quickly become clogged with construction dirt 
and debris, which may cause system damage.

WARNING! 

To avoid the release of refrigerant into the 

atmosphere, the refrigerant circuit of this unit must be 
serviced only by technicians who meet local, state, and 
federal profi ciency requirements.

WARNING! 

All refrigerant discharged from this unit must 

be recovered WITHOUT EXCEPTION. Technicians must 
follow industry accepted guidelines and all local, state, 
and federal statutes for the recovery and disposal of 
refrigerants.  If a compressor is removed from this unit, 
refrigerant circuit oil will remain in the compressor. To 
avoid leakage of compressor oil, refrigerant lines of the 
compressor must be sealed after it is removed.

Safety

Warnings, cautions and notices appear throughout this 
manual. Read these items carefully before attempting any 
installation, service, or troubleshooting of the equipment. 

DANGER: Indicates an immediate hazardous situation, which 
if not avoided will result in death or serious injury. DANGER 
labels on unit access panels must be observed.

WARNING: Indicates a potentially hazardous situation, which 
if not avoided could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation or an 
unsafe practice, which if not avoided could result in minor or 
moderate injury or product or property damage.

NOTICE: Notifi cation of installation, operation or maintenance 
information, which is important, but which is not hazard-
related.

Summary of Contents for RPVE Series

























































Reviews: