background image

DANGER!

WATER TEMPERATURE SETTING

Safety and energy conservation are factors to be considered when selecting the water
temperature setting . Water temperatures above 125 F
from scalding. Be sure to read and follow the warnings

o

can cause severe burns or death

outlined on the label pictured below.

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.

Water temperature over 125 F can
cause severe burns instantly or
death from scalds.

°

Water Temperature

Time To Produce a Serious Burn

125 F

o

1 /

1 2

to 2 minutes

130 F

o

About 30 seconds

135 F

o

About 10 seconds

140 F

o

Less than 5 seconds

Table courtesy of Shriners Burn Institute

DANGER: Households with small children,

disabled, or elderly persons may require a 120 F.
Or lower temperature setting to prevent contact
with

HOT

water.

o

4

The factory setting allows operating

temperatures between 90 F and 140 F.

Notice:

o

o

The temperature of the water at the outlet of the
water heater can be regulated by setting the
temperature on control panel . The control panel was
set at 110 F before it was shipped from the factory.

o

The illustration to the bottom left illustrates the
control panel and how to adjust the water
temperature.

Notice:

When this water heater is supplying general

purpose hot water requirements for use by
individuals, a thermostatically controlled mixing
valve for reducing point of use water temperature is
recommended to reduce the risk of scald injury.
Contact a licensed plumber or the local plumbing
authority for further information.

The chart shown above may be used as a guide
in determining the proper water temperature for your
home.

Maximum water temperature occurs while burner is
on. To find water temperature being delivered, turn
on a hot water faucet and place a thermometer in the
water stream and read the thermometer.

Children, disabled and elderly are
at highest risk of being scalded.

Temperature limiting valves are
available, see manual.

See instruction manual before
setting temperature at water
heater.

Feel water before bathing or
showering.

Time/Temperature Relationship in Scalds

120 F

o

More than 5 minutes

F

ON/OFF

UP

DOWN

Output Temp

Set Temp

Error Code

145 F

o

Less than 3 seconds

150 F

o

About 1 /

1 2

seconds

155 F

o

About 1 second

Summary of Contents for Residential Indoor Gas Tankless Water Heater















Reviews: