background image

 

31 

WARRANTY NOTE 

 
The  solar  water  heater  and  its  components  are  covered  by  a  comprehensive 
warranty. For full details, refer to the Owners Guide and Installation Instructions 
supplied with the solar storage tank. 
 
The part extracts from the Warranty Condition (5) and Warranty Exclusions (c), 
(d),  (g),  (h)  and  2  of  the  water  heater  Warranty  should  be  noted  before 
commencing the installation of the solar collectors. 
 
The  term  “water  heater”  used  in  the  Warranty,  Warranty  Conditions  and 
Warranty  Exclusions  means  the  Manufacturer  supplied  water  heater(s),  solar 
storage tank(s), solar collector(s), kit(s) and components. 
 

WARRANTY CONDITIONS 

5.

 

Where the water heater is installed in a position that does not allow safe, ready access, the 

cost of accessing the site safely, including the cost of additional materials handling and / or 
safety equipment, shall be the owner’s responsibility. 

 

WARRANTY EXCLUSIONS 

c)

 

Where the water heater or water heater component has failed directly or indirectly as a result 
of:  excessive  water  pressure;  excessive  temperature  and / or  thermal  input;  blocked 

overflow / vent drain; corrosive atmosphere; non approved or incorrectly mixed closed circuit 
fluid being used; incorrect or insufficient filling of the  indirect  closed  circuit system with the 
closed circuit fluid; ice formation in the pipe work to or from the water heater. 

 

d)

 

Where the solar water heater or solar water heater component has failed directly or indirectly 

as  a  result  of  ice  formation  in  the  water  ways  of:  a  solar  water  heater  system  where  the 
system has not been installed in accordance with the water heater installation instructions; an 
indirect  closed  circuit  system  due  to  non  approved  or  incorrectly  mixed  closed  circuit  fluid 
being used; an indirect closed circuit system where there is insufficient or incorrect fall in the 
pipe work preventing complete drain back of the closed circuit fluid. 

 

g)

 

Where  the  water  heater  has  been  connected  at  any  time  to  a  water  supply  that  does  not 
comply  with  the  water  supply  guidelines  as  outlined  in  the  Owner’s  Guide  and  Installation 
Instructions. 

 

h)

 

Breakage  of  collector  glass  for  any  reason  including  hail  damage  (we  suggest  that  the 

collector glass be covered by your home insurance policy). 

 

2.

 

SUBJECT  TO  ANY  STATUTORY  PROVISIONS  TO  THE  CONTRARY,  THIS  WARRANTY 
EXCLUDES  ANY  AND  ALL  CLAIMS  FOR  DAMAGE  TO  FURNITURE,  CARPETS,  WALLS, 
FOUNDATIONS  OR  ANY  OTHER  CONSEQUENTIAL  LOSS  EITHER  DIRECTLY  OR 
INDIRECTLY DUE TO LEAKAGE FROM THE WATER HEATER, OR DUE TO LEAKAGE FROM 
FITTINGS AND / OR PIPE WORK OF METAL, PLASTIC OR OTHER MATERIALS CAUSED BY 
WATER TEMPERATURE, WORKMANSHIP OR OTHER MODES OF FAILURE. 

 

Summary of Contents for NPT 200

































Reviews: