Rheem 90RS04EES Series Installation Instructions Manual Download | Manualshive

Page: 46 / 60

background image

46

FURNACE TWINNING
INSTALLATIONS

Twinning operation of two furnaces,
installed side-by-side, connected by a
common duct system with main
power supplied by the same source.

IMPORTANT:

Twinning of these units

requires an accessory twinning kit.
Refer to the specification sheet for
proper kit. Do not attempt to twin
these models by using the
instructions below.

IMPORTANT:

Only twin furnaces with

identical control boards.

IMPORTANT:

Only bottom returns

can be used. No more than two
furnaces can share the same supply
and return. Furnaces must have
same heating and blower capacity.
Twinning furnaces must operate off
the same phase of power.

It should be noted that both blowers
will run simultaneously when there is
a call for heating, cooling or fan.

The “OK” LED will flash if twinning is
not set up properly.

fireplace, sun rays, lamps, televisions,
radios or air streams from registers.
Refer to instructions packed with the
thermostat for “heater” selection or
adjustment.

ACCESSORIES

FIELD-INSTALLED
OPTION ACCESSORIES

ELECTRONIC AIR CLEANER

(EAC)

NOTE:

A spade terminal for EAC is

provided on these models.

HUMIDIFIER

NOTE:

Humidifier output is not

available on these models.

ALTERNATE (LEFT SIDE)
DRAIN KIT - RXGY-H01
(DOWNFLOW MODELS
ONLY)

«
...
44
45
46
47
48
...
»

Summary of Contents for 90RS04EES Series





























































Reviews:

No comments

Related manuals for 90RS04EES Series

Brand: York Pages: 8

Brand: Bryant Pages: 60

Brand: Lennox Pages: 51

Brand: Hotblast Pages: 60

Brand: Lennox Pages: 52

Brand: Carrier Pages: 8

Induced Combustion Gas Furnace

Brand: Carrier Pages: 10

Brand: Fire Chief Pages: 28

Brand: Rapid Pages: 58

Brand: Empire Heating Systems Pages: 64

Brand: Empire Heating Systems Pages: 64

Brand: ICP Pages: 44

DIVAtech D HF24

Brand: Ferroli Pages: 64

Brand: Ducane Pages: 6

Brand: Allied Pages: 36

Brand: Allied Pages: 46

Brand: Allied Pages: 55

Brand: Allied Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands