Rheem 90RS04EES Series Installation Instructions Manual Download

Page: 29 / 60

RXGY-G02 SIDE WALL VENT

This termination for horizontal venting
only.

IMPORTANT:

Do not install on the

prevailing winter wind side of the
structure. Observe same clearances
specified for horizontal, standard
termination.

NOTE:

Multi-venting-No common

venting.

NOTE:

Install the vent and air intake

piping into the vent plate openings.
Seal all gaps between the pipes and
wall.

Be Sure To Use Silicone

Sealant

to seal the vent pipe to the

vent cap to permit field disassembly
for annual inspection and cleaning.
Also seal all pipe penetrations in wall.
To prevent possibility of condensate
freeze-up or recirculation,

do not

install vent kits one above the
other.

NOTE:

The vent illustration in Figure

21 can be used for Non-direct vent
terminations also.

FIGURE 21

VENT KIT INSTALLATION OPTIONS

FIGURE 20

VENT KIT INSTALLATION OPTIONS

EXHAUST

AIR
INTAKE

For 90000 thru 120000 BTUH models-

reduce to a length between 12 inches

and 30 inches of 2 inch pipe.

for 45000 thru 75000 BTUH models-

when 3 inch pipe is used: reduce last 30

inches to 18 inches of 2 inch pipe and

12 inches of 1-1/2 inch pipe to maintain

velocity.

Note:

Vent should protrude a

maximum of 2-1/4” beyond vent plate.

Air intake should protrude a maximum

of 1 inch beyond vent plate.

Seal all wall cavities

Summary of Contents for 90RS04EES Series





























































Search results

Summary of Contents for 90RS04EES Series

Reviews:

Related manuals for 90RS04EES Series

Brands by name

Popular brands

Rheem 90RS04EES Series, Installation Instructions Manual

Search results

Summary of Contents for 90RS04EES Series

Reviews:

Related manuals for 90RS04EES Series

Brands by name

Popular brands