manualshive.com logo in svg

Rheem 136-1826, Operating And Installation Manual, Page: 8 / 55

Share
Download
Rheem 136-1826 Operating And Installation Manual Download Page 8

BASE REQUIREMENTS

Indoor water heaters must be installed on a level noncombustible surface, except as noted below.  

Do not install

on carpeting.  

Heater sizes 926 to 1758 Typhoon (Outdoor) are supplied with a combustible flooring base as

standard.  The following chart lists the part number required for a combustible base, for water heaters supplied
without a combustible base.

COMBUSTIBLE FLOOR BASE

   BOILER     PART     BOILER     PART     BOILER     PART       BOILER      PART
      136

   001749        399     058316        825     056202         1337       059236

      181

   058313        512     056199        962     059233         1467       059237

      264

   058314        627     056200      1125     059234         1630       059238

      331

   058315        726     056201      1223     059235         1826       059239

Fig. #8276

Hollow concrete cinder block; align holes and leave ends open.

Alternative method for providing a non-combustible base.

HEATER INSTALLATION

ON CONCRETE BLOCKS OR TILE

HEATER WITH COMBUSTIBLE

FLOOR SHIELD

Fig. #8148.1

8

Summary of Contents for 136-1826
























































Reviews:

No comments