background image

 

 

SAFETY INFORMATION  

 

WARNING: 
BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND

 

THE 

FOLLOWING SAFETY INSTRUCTIONS.FAILURE TO FOLLOW

 

WARNING 

COULD RESULT IN DEATH OR SERIOUS INJURY.

  

 

1. WEAR SAFETY GLASSES OR GOGGLES.

  

Danger to the eyes always exists due to the possibility of dust being blown

 

up by the 

exhausted air or of a fastener flying up due to the improper

 

handling of the tool. For 

these reasons, safety glasses or goggles shall

 

always be worn when operating the 

tool. The employer and/or user must

 

ensure that proper eye protection is worn. The employer 

is responsible to enforce the use of eye protection equipment

 

by the tool operator and all other 

personnel in the work area.

 

NOTE: Non-side shielded spectacles and face shields alone do not 

provide

 

adequate protection. 

 

2. EAR PROTECTION MAY BE REQUIRED IN SOME ENVIRONMENTS. 

As the working condition may include exposure to high noise levels which can

 

lead 

to hearing damage, the employer and user should ensure that any

 

necessary 

hearing protection is provided and used by the operator and others

 

in the work area. 

 

3. DO NOT USE ANY POWER SOURCE EXCEPT AN AIR COMPRESSOR. 

The tool is designed to operate on compressed air. Do not operate the tool on

 

any 

other high pressure gas, combustible gases (e.g. Oxygen, acetylene, etc.)

 

since 

there is the danger of an explosion. For this reason, absolutely so not

 

use anything 

other than an air compressor to operate the tool. 

 

4. OPERATE WITHIN THE PROPER AIR PRESSURE RANGE. 

The tool is designed to operate within an air pressure range of 70 psi 
to100 psi (5 to 7 bar). The pressure should be adjusted to the type of the 
work being fastened. The tool shall never be operated when the operating 
pressure exceeds 120 psi. (8.3 bar). 

 

5. DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE. 

Never operate the tool near a flammable substance (e.g., thinner, gasoline, etc.). 
Volatile fumes from these substances could be drawn into the compressor and 
compressed together with the air and this could result in an explosion. 

 
 
 

Summary of Contents for CN565X















Reviews: