background image

 

DTR_301-D3-XX-001_EN_a

 

1

 

Manufacturer 

RGB Technology Sp. z o. o. 
Tymieo 18 
76-035 Tymieo 
POLAND 

 

2

 

Specifications 

ZAS10-L PoE 

Dimensions of the device (WxHxD): 

350mm x 170mm x 44mm / 13.8in x 6.7in x 1.7in 

Display format:  

HH:MM 

Digit height:  

101,6mm / 4in 

Weight of the device: 

1.7kg / 3.75lbs 

Casing tightness rating

1

 IP: 

4X 

Power supply: 

IEEE 802.3af(PoE), IEEE 802.3at (PoE+) 

Average power consumption of the device: 

3,5W 

Device operation temperature (ambient): 

-25°C ÷ 45°C / -13°F ÷ 113°F 

Device operation temperature (device surface) 

-25°C ÷ 60°C / -13°F ÷ 140°F 

3

 

Transport and storage 

Care should be taken to properly protect the devices so as to eliminate any damage during transport. It is forbidden to 
transport  the  devices  in  a  collective  package  without  adequate  amortisation  -  each  device  must  be  packed 
separately and cannot have freedom of movement during transportation.  

Due  to  the  protective  packing  the  module  should  be  stored  in  the  temperature  not  lower  than  -25°C  and  not 
higher than +60°C at the humidity below 99%RH. 
 

4

 

Device construction  

ZAS10-L PoE is cased in a powder-coated steel housing. The properly installed device meets the IP4X tightness 
requirements. 
The figure shows ZAS10-L PoE clock

2

 

det. A

 - case; 

det. B

 - AM/PM indicator; 

det. C

 - synchronization error indicator; 

det. D

 - lighting sensor; 

det. E

 - lR sensor;  

det. F

 - cable outlet; 

det. G

 - Ethernet connector 

fig. 1 

 

 

                                                           

1

  Specified on the basis of EN 60529.

 

2

 

Explanatory figure.

 

Summary of Contents for ZAS10-L PoE








Reviews: