background image

—

 

Power: 23A 12V battery. 

—

 

Transmitting Range: 100m. 

—

 

Safety ON/OFF switch prevents misfires. 

2)  Receiver 

—

 

Model No.: RF12 

—

 

Cue: 12 cues 

—

 

Power: (Either internal or external) 

Internal batteries: 6xAA battery, rechargeable 
or disposable;  
External battery: 12VDC, SLA is recommended. 

—

 

Firing current: >750mA, Max. 10A 

—

 

Test current: <40mA 

—

 

Size: 154mmx108mmx38mm, antenna is 
retractile and foldable. 

 
Parts 
1- Telescopic Antenna 

 

2- Wired Control LED 
3- Digital Readout Meter 
4- External Battery Jack 
5- Negative Terminals for cues 
6- Learn Button   
7- Positive Terminals for cues 
8- Arm LED / Learn LED 
9- Rocker Switch, 3 positions Test / Learn / Arm 
10- Cue Fire LED, total 12 LEDs 
11- Cue Test LED, total 12 LEDs 

12- Main Switch, lock switch 
13- RS485 ports 
14- Battery Cover 
15- Battery Enclosure 
 
  3)  Components: 

 

 

 

RF12 Transmitter 

A TCF100-12LN 

Transmitter B TCF100-12LNX 

1 pcs, basic unit 

1 pcs, basic unit 

1 pcs, optional 

 

 

 

Alligator Clip Wire 

AA Battery 

SLA Battery 

1 pc, basic unit 

6 pcs, optional 

1 pcs, optional 

Summary of Contents for MS Series







Reviews: