manualshive.com logo in svg

RFE DS 1000W, User Manual

Share
Download
RFE DS 1000W User Manual Download Page 42

43

USER MANUAL - TRANSMITTER DS SERIES - 30 - 50 - 100 - 500 - 1000W

Rev 1.3

Reset & Upgrade Firmware via Lan Address

This  procedure  is  intended  for  the  upgrade  of  the  internal  Firmware  of  the  RFE 

Transmi  ers.

Requirements

•  Personal Computer running Windows versio 7 to 10.

•  Standard Lan Cable.

•  TFTP Client So  ware (f.e. Weird “  tpc_free”)

 

 

it can be dowloaded here: 

h  ps://www.weird-solu  ons.com/dowloads/

u  li  es

.

•  Standard  Firmware  fi le;  (for  example  “

Firmware-TX-7.62b.bin” 

to  upgrade  a 

transmi  er to fi rmware version 7.62b).

Firmware Reset Procedure

1.    Confi gure  the  PC  on  the  same  class  of  IP  addresses  of  the  Transmi  er  (for 

example 192.168.178.1) 

2.  Connect it with a cable to the LAN connector on the rear panel (fi gure C1) of the 

TX/Amplifi er.

3.  Launch the TFTP Client  So  ware.

4.  Confi gure the Client as in Figure C2:

  - TFTP server: 

Lan address of the TX (i.e. 192.168.178.99)

- Opera  on: 

Upload

  - Format: 

Binary

  - Local File Name: click on the folder bu  on and select the fi le, for example 

“

Firmware-TX-7.62b.bin”

  - Remote File Name: 

tx_fi rmware.bin

 (Be carefully

Be carefully!!! Other fi le name doesn’t 

work).

Summary of Contents for DS 1000W

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands