manualshive.com logo in svg

RFE DS 1000W, User Manual

Share
Download
RFE DS 1000W User Manual Download Page 25

Rev 1.3

USER MANUAL - TRANSMITTER DS SERIES - 30 - 50 - 100 - 300 - 500 - 1000W

26

The displayed readings are:

•  Ipa 1-2-3: currents supplied by the power supplies;

•  3v3/5v0/Serv: service voltages;

•  Vpa: Voltage power amplifi er, the voltage with which the RF is working;

•  Eff : effi  ciency in percent;

•  RF: RF heatsink temperature in Celsius degrees;

•  Amb: room temperature in Celsius degrees.

In the main panel of se   ng, fi nally it is possible to enable or disable:

•  FSK

•  19kHZ Out

•  GMT En

Lan confi guration

From this panel it is possible to confi gure the connec  on parameters to the LAN of 

your system Transmi  er. You can set the IP address, the Subnet Mask, the Gateway, the 

Domain Name Server, and the Network Time Protocol Server address set by default at 

193.204.114.232 and you can enable GMT synchroniza  on with the server. 

Touching  the  IP  address  to  be  confi gured  will  open  the  panel  for  confi guring  its 

address as shown in the fi gures.

Fig. 14: Lan confi gura  on

Summary of Contents for DS 1000W

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands