Rf-t AVANTAGE DP, Manual, Page: 14 / 19

14
Installation
Installation into vertical shaft with built-in mounting frame: general instructions for all types of shafts (other than concrete)
The product was tested and approved in:
Product Range Wall type Classification
Avantage 60 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Promatect L500 ≥ 30 mm EI 60 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 60 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Geoflam ≥ 30 mm EI 60 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 60 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Geotec ≥ 30 mm EI 60 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 60 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Tecniver ≥ 35 mm
EI 60 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 60 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Glasroc F V500 ≥ 35 mm EI 60 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 60 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Exthamat ≥ 25 mm EI 60 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 60 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Desenfire HD ≥ 25 mm HD EI 60 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Promatect L500 ≥ 40 mm
EI 90 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Geoflam ≥ 35 mm EI 90 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Tecniver ≥ 45 mm EI 90 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Exthamat ≥ 30 mm EI 90 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Desenfire ≥ 25 mm THD
EI 90 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Promatect L500 ≥ 50 mm EI 120 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Geoflam ≥ 45 mm EI 120 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Geoflam Light ≥ 35 mm EI 120 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Geotec ≥ 45 mm
EI 120 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Exthamat ≥ 35 mm EI 120 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Tecniver ≥ 50 mm EI 120 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Glasroc F V500 ≥ 50 mm EI 120 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Desenfire HD ≥ 35 mm HD EI 120 (v
ed
i
n
o) S 500 C10000 AA multi
Avantage 120 350x385 mm ≤ Avantage 1V DP ≤ 700x1075 mm Shaft Desenfire ≥ 45 mm EI 120 (v
ed
i
n
o) S 500 C10000 AA multi
AVANTAGE DP
e
≥ 105 mm
e
A = 2 x e + 10 mm
(W+
A
) x (H+
A
) mm
(W+10) x (H+10) mm
1. Make an opening with dimensions (W+A) x (H+A) mm.
A = 2 x thickness sleeve (e) + 20 mm.
Fit a sleeve of the same type and thickness of the duct (thick-
ness e) of minimum 105 mm deep in the opening.
Fix the sleeve to the shaft wall. 2. Two sealing lugs are provided at the bottom and at the top of
the mounting frame: fold these against the sleeve.
In case of fixing by screws, fasten the mounting frame to the
sleeve with chipboard screws (Ø 6 x e) mm. These screws can
be fixed in one of the openings provided for this purpose,
depending on the depth of the sleeve.
Take care not to misshape the frame during its installation. The
finished opening must be the same size as the mounting frame
(W+10) x (H+10) mm.
1 2