BLUESWITCH Access Control
BLUESWITCH Access Control
BLUESWITCH Access Control
BLUESWITCH Access Control
DS 10208-1
©2009 REG No 277 4001, Lewes, England. Page 3
Learning
Learning
Learning
Learning a
a
a
a new
new
new
new BT
BT
BT
BT de
de
de
dev
vv
vice:
ice:
ice:
ice:
1.
Ensure the device to be learned is the only Bluetooth device within range.
2. Connect the jumper SIL2 across pins
a
and
b
.
3. BLUESWITCH will scan for devices for 10 seconds.
Each time it detects a Bluetooth device, LED D4 will extinguish briefly.
(
Note: If D4 flashes rapidly, all128 storage locations are full.)
At the end of the 10 seconds:
-
If no devices were detected, step 3 repeats.
-
If one device was detected, it will be added to the list of recognized devices and D4 will go
out. Proceed to step 4.
-
If more than one device was detected, step 3 repeats.
4. Remove the jumper from SIL2.
Erase
Erase
Erase
Erase all
all
all
all devic
devic
devic
device
e
e
es
s
s
s from
from
from
from t
t
t
th
h
h
he
e
e
e BLUESWITCH
BLUESWITCH
BLUESWITCH
BLUESWITCH
Memory:
1.
Connect a jumper across SIL3 pins
b
and
c
. LED D4 will light.
2.
Press and hold pushbutton SW1. LED D4 will go out. Hold for at least five seconds.
3.
LED D4 will flash slowly indicating that all recognized devices have been deleted.
4.
Remove the jumper link across SIL3.
Setting the Relay
Setting the Relay
Setting the Relay
Setting the Relay Time
Time
Time
Time
The Relay 2 operating time may be set between 1 and 255 seconds. The factory setting is 1 second.
In
Auto Mode
, this is the time Relay 2 operates for, once recognized phones are no longer de-
tected.
In
Arrival-Only Mode
, it is the time since the Relay 2 started operating.
In
Semi-Auto Mode
, it is the since the button was released
.
.
To
To
To
To set
set
set
set t
t
t
the
he
he
he timed
timed
timed
timed action
action
action
action d
d
d
delay:
elay:
elay:
elay:
1. Connect a jumper across SIL3 pins
b
and
c
. LED D4 will light.
2. Briefly press pushbutton SW1. (Do not hold it down – that erases all devices!)
The LED will flash quickly.
4. Wait for the duration that the output is to operate for, then press pushbutton SW1 again.
The LED will stay lit to indicate the operation is complete.
5. Remove the jumper link across SIL3.
Setting the Dete
Setting the Dete
Setting the Dete
Setting the Detec
c
c
ction Ra
tion Ra
tion Ra
tion Ran
n
n
nge
ge
ge
ge
1.
Press and hold down pushbutton SW1.
2 .
Connect a jumper across SIL3 pins
b
and
c
.
D5 wiil light until step 7.
3.
Release SW1.
4.
LED D4 will repeatedly show a series of flashes:
One flash indicates the current range setting is 1,
Two flashes indicates setting 2, etc.
5 .
Press pushbutton SW1 as many times as the setting
required. e.g. for setting 3, press 3 times.
6.
LED D4 will repeatedly flash to show the new setting.
7.
Remove the jumper link across SIL3.
Notes
Notes
Notes
Notes
Range is approximate and will depend on operating environment.
*If phone is Class II then the range may be limited to 10m-20m.
Detection Range Settings
(Approximate! Depending on condi-
tions)
Setting
~Range
1
1.5 m
2
3 m
3
5 m
4
9 m
5
15 m
6*
30 m
7*
50 m
