Reynolds Building Systems EZ up Sheds Ashbury Assembly Book Download | Manualshive

Page: 3 / 11

background image

6.

Repeat to assemble another floor section.

Step 1

Assemble Floor

3. Remove the (2) two loose 2x4 floor joists.

4. Install (3) three 87" long treated floor joists, between the 48" long boards.

Use 16d galv. deck nails.

5. Install an OSB flooring panel over the floor frame. Use 8d spiral deck nails,

space nails 12" apart.

1. After removing all material from the pallet/floor, turn the pallet over.

2. Remove the 2x4-4'shipping cleats.

2x4-87" Floor joist

2x4-48" Board

5/8" Flooring

«
1
2
3
4
5
...
»

Summary of Contents for EZ up Sheds Ashbury












Reviews:

No comments

Related manuals for EZ up Sheds Ashbury

Brand: Palmako Pages: 69

Brand: STILLA Pages: 32

Brand: STILLA Pages: 44

Brand: STILLA Pages: 48

Brand: Swiss Pet Pages: 2

Brand: Palmako Pages: 119

Brand: Palmako Pages: 45

Brand: Karibu Pages: 37

Brand: Karibu Pages: 36

Brand: Palmako Pages: 78

Santa Rosa SR812-FJ-Metal

Brand: OLT Pages: 56

Brand: Palram Pages: 83

Meridian 8' x 12' Gable 16698

Brand: Handy Home Products Pages: 63

Brand: aivituvin Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands