manualshive.com logo in svg

Reynolds Building Systems Best Barns Weston, Assembly Book, Page: 2 / 20

Share
Download
Reynolds Building Systems Best Barns Weston Assembly Book Download Page 2

Always wear safety glasses when cutting or nailing!

I

MPORTANT

 I

NFORMATION

 A

BOUT

 Y

OUR

 K

IT

Delivery:

Insure you receive 1 pallet and 1 bundle of lumber. A second delivery from a home

center will contain pre-cut wall studs and sheet goods.

Items not included:

Shingles, vinyl siding, woof floor, garage door and windows are purchased

separately.

Garage door:

An 8ft. wide x 7ft. high door is required.

Prior to building:

Unpack all items and organize items according to size and type. This will make them easier to find
when instructed. DO NOT discard any material until your building is complete.

Check with your local permitting authority to obtain any required documentation.

Thoroughly read this manual. DO NOT skip outlined steps.

Tools Required:

Hand or Circular Saw

Cordless Drill

Hammer    Phillips Screwdriver   Framing Square

Level    Measuring Tape    Step Ladders (two recommended)    Safety Glasses    Dust Mask

Terminology:

Plumb:

Checking to see if a wall is vertical

Wall Plate: Top and bottom 2x4s used to frame walls

Tie Plate:

Second layer of 2x4s connecting wall sections together

Header:

Spans top of door opening

OSB:

Oriented strand board used for sheathing walls and trusses

Material lists located on back page.

Questions: Call 800-245-1577 8am-5pm EST. After hours call 724-866-4357. Or email
[email protected]

Summary of Contents for Best Barns Weston





















Reviews:

No comments