manualshive.com logo in svg

Reynolds Building Systems Best Barns Weston, Assembly Book, Page: 16 / 20

Share
Download
Reynolds Building Systems Best Barns Weston Assembly Book Download Page 16

Step 17

Install Gable & Door Trim

1.

Install a keystone and gable trim

under the roof sheathing as done
in Step 13.

1.

Locate (2) two 1x4-6' trim boards. Cut each

to fit against back of front gable trim and
install on the side walls.

2.

Locate (2) two 84" long x 3-7/8" wide primed siding.

Cut to fit and install on the sides of the door opening
flush with front wall OSB. Use 6d galv. nails.

1x4 Gable Trim

1x4 Gable Trim

1x4 Fascia

Siding Extends 3/4” Below Trim

Step 18

Finish Side Wall Trim

Keystone Trim

3.

Install a keystone trim board 3/4” above the center of the

door opening. Use 6d galv. nails. The exposed siding will
serve as a door stop when the doors are closed.

4.

Install (2) two 1x4-84" long trim boards flush to the sides

of the door opening flush with jamb and top of trim 3/4"
above door opening. Tack these boards with a couple
nails, you may want to reposition the trim when you install
the doors.

5.

Locate 1x4 trim boards with an angle cut on one end.

Install these agains the keystone. Cut boards so to be flush
with outside of vertical trim.

Summary of Contents for Best Barns Weston





















Reviews:

No comments