background image

LIMITED WARRANTY

REYCO-GRANNING 23AR/25AR/30AR SERIES

AIR SUSPENSION SYSTEMS AND COMPONENTS

Tuthill Transport Technologies (The Company)  warrants suspension products manufactured by it to be free from defect
in material and workmanship which occur under normal use and service subject to the following conditions and limita-
tions:

1. Coverage is per below in months or in kilometers/miles depending upon which occurs first.

** For Off Road Applications Coverage Will Be For 24 Months Parts and Labour or 48 Months Parts Only

2. This warranty shall not apply and no warranty of any kind shall exist as to any product which has been subject to

abuse, misuse, neglect, misapplication or accident of any type or cause or which has been repaired, replaced,
substituted or used with parts other than genuine parts of The Company or altered by anyone.

3. The Company shall not be liable for the loss of any product, loss of time, inconvenience, commercial loss or any

other indirect consequential, special or incidental damages due to breach of the above warranty or any other 
failure to comply with the terms of the contract between The Company and the Buyer. The Company makes no
warranties of any kind, express or implied, other than as herein expressly provided,and specifically disclaims the
implied warranties of merchantability and fitness for a particular purpose.

4. With respect to parts manufactured by others, The Company shall have no duty except to assign to the buyer

any claim which The Company may have against the manufacturer thereof.  (The Company Warrants purchased
components to the same extent as the Warranty extended by the original manufacturer to The Company).

5. The determination of the reasonable cost of labour as required in paragraph one (1), shall be made in accordance

with The Company shop standard times. Maximum hourly allotment for labour cost is as determined by 
The Company annually. Shop standard times and maximum hourly allotment for labour cost may be revised 
periodically at the sole discretion of The Company.

6. The Company is not responsible for damage from improper installation or operations beyond design capability.

The Company, in its sole discretion, shall determine whether or not any product  is defective or otherwise 
covered, or not covered by, this warranty. No action for breach of this warranty may be commenced more than
one year after the occurrence of alleged breach. This warranty is not transferable.

COMPONENT

MONTHS

KILOMETERS/MILES

COVERAGE PROVIDED

Air Controls

0 - 60

800,000/500,000

Parts and Labour Allowance

Air Springs

0 - 60

800,000/500,000

Parts and Labour Allowance

Shock Absorbers

0 - 12

160,000/100,000

Parts and Labour Allowance

Hangers, Trailing Arms

0 - 24

320,000/200,000

Parts and Labour Allowance

25 - 60

800,000/500,000

Parts Only

Bushings for Trailing Arms 52”

0 - 60 

800,000/500,000

Parts and Labour Allowance

Spacing or Less Van Type

61 - 84

1,200,000/750,000

Parts Only

Application

Bushings for Trailing Arms

0 - 36

480,000/300,000

Parts and Labour Allowance

All other applications**

0 - 60

800,000/500,000

Parts Only

M-15

Summary of Contents for 23AR



















Reviews: