REX RG-RH Operation Manual Download Page 7

Page: 7 / 18

- 5 -

4. Setting Up

1. Setting Up

㧍

CAUTION

1) Attaching the Mount Kit:

Fix the mount kit to the main body securely
with the eight bolts (M10 x 25) and their
corresponding spring washers (10 mm). (Fig. 2)

㨯

Always attach the mount kit that matches the

pipe threading machine used. The mount kit
cannot be attached to the pipe threading
machine correctly if a mount kit for a
different type of machine is used.

Which pipe threading machine it can be

attached to is indicated on the mount kit.

Attach the mount kit in the correct direction.

(Fig. 2)

㨯

If the mount kit is attached in the opposite

direction, an unnecessary load will be applied
to the threading machine's chuck, thereby
resulting in damage.

Fig. 2

Bolt (M10 x 25)

Spring washer (10mm)

Mount Kit

Hook

Code No.

Table 1 Mount Kit

Name

For use with

M-HR1 REX 50A

M-HR2 REX 80A

M-HR3 REX100A

M-HE1 #300

N50A, NP50A, NR50A, P50A, R50A, NPG150A

(Cannot be used on the NT50.

㧕

S80A, N80A, NP80A

N100A

#300

341560

341561

341562

341563

Mount Kit

Summary of Contents for RG-RH



















Search results

Summary of Contents for RG-RH

Reviews:

Related manuals for RG-RH

Brands by name

Popular brands

REX RG-RH, Operation Manual

Search results

Summary of Contents for RG-RH

Reviews:

Related manuals for RG-RH

Brands by name

Popular brands