manualshive.com logo in svg

REVV Generator 120, Owner'S Manual

Share
Download
REVV Generator 120 Owner'S Manual Download Page 33

Revv Owner’s Manual - 33

Note: There are only 4 channel LED, so the MIDI channel count will be 

done in values of 4. MIDI channel 1 will be signified by CH1 CLEAN LED 

flashing, & as you increase in number, MIDI channel 4 will be signified by 

all four channel LEDS flashing, but once MIDI channel 5 is selected, only 

the CH1 CLEAN LED will flash again. Every time you reach MIDI channel 

5, 9, or 13, the LED cycle will once again start from the CH1 CLEAN LED. 

So keep count as you select the channel you desire. If you go past MIDI 

channel 16, the count will start at channel 1 again. Once saved to 

memory, the Channel LEDs will flash very quickly a number of times to 

verify the change has been made & completed. The amp will then 

restart, completing the MIDI channel change procedure. 

MIDI Program Change

This amplifier can remember up to 128 program settings of the MIDI con-

trollable functions. In order to set a program (i.e. amplifier configuration) to 

be controlled via MIDI: 

1)

 Set the amplifier to the configuration you intend to save to a program 

number. (Ex: Ch: 3, Aggression level: 2, Fat: ON, Master Volume: 2, FX 

Loop: OFF, etc) 

2)

 Once the amplifier is configured as you would like, press the store 

switch. The Store LED will flash & the amplifier will wait now for a com-

mand through its MIDI IN jack. 

3)

 Send a program change command from your MIDI Pedal or other 

equipment with the correct channel & program number you intend to 

have the amplifier save the current configuration to. 

4)

 Once the command is received, the amplifier will save the current amp 

configuration to that program number. The Store LED will flash 3 times & 

turn off verifying that the command has been received & saved. 

6.3

Summary of Contents for Generator 120












































Reviews:

No comments

Brands by name

Popular brands

Load more brands