manualshive.com logo in svg

REVV Generator 120, Owner'S Manual

Share
Download
REVV Generator 120 Owner'S Manual Download Page 16

Revv Owner’s Manual - 16

Standby & Power Switch 

D - Store Switch 

The store switch is used to program MIDI as well as set the MIDI channel. 

When the amplifier is powered up, by pressing the store toggle switch 

down, the store LED will begin to flash. At this point, the amplifier is waiting 

for a MIDI program command to be received. Once received, the current 

amplifier configuration will then be saved to memory so that anytime the 

program command is received via MIDI; the amp will switch itself to the 

saved configuration. 

Note: When in store mode, once a MIDI program command is received, 

the LED will flash quickly then turn off - signaling the user that a program 

command has been received & the amp’s configuration has been stored 

to memory. 

The power & standby switches give the amp power from the mains, as 

well as high voltage through the circuit. First turn on the power switch & 

wait one minute to allow the tubes to warm up. Turn on the standby 

switch to the Revv position once you are ready to play. 

Note: NEVER power up the amplifier without the proper speaker load 

connected! 

2.9

Summary of Contents for Generator 120












































Reviews:

No comments

Brands by name

Popular brands

Load more brands