3.2 MOUNTING HOLES
There are special mounting holes in the back flange of the fan. Using them,
it is possible to mount the device with e. g. mounting pins. In order to dampen
possible vibrations of the structure, it is recommended to use anti-vibration
mounts. Necessary assembly elements, suitable for this type of installation,
should be purchased independently.
4. INSTALLATION INSTRUCTIONS
4.1. CONNECTION OF THE DEIVCE TO THE ELECTRICAL SYSTEM
-
all works concerning electrical installation should be made by the qualified
personnel (who possess required authorizations to install electrical equipment),
based on wiring schematic diagrams (see 7)
-
the electrical installation of the building shall have a residual current device
-
it is recommended to check the electric installation and controls before the first
start
5. PRECAUTIONS & WARNINGS
The precautions mentioned below must be strictly followed during operation
of the device:
- all works concerning electrical installation (disassembly, repair etc.) should
be made by the
qualified staff, who possess the qualifications due to the domestic
and local norms, regarding electrical installations
- before service or exchange of the device it is obligatory to cut off the current
supply
- do not limit or cover the inlet and outlet of the device
- do not install, service the device with wet hands or barefoot
- the device should be kept out of reach of children and animals
-
after operating time of the device, please utilize it concerning the local norms
and regulations
ź
-
i
t is recommended to clean the device periodically (at least twice a year)
:
air stators, fan casing and blades clean from dirt
-failure to comply with cleaning obligations may have a negative effect
on technical parameters of the device
and lead to loss of warranty
-
i
f the device is not used for a longer time and lead to loss of warranty
disconnect
the voltage supply
-
the device is transported with the closed air stators. It is essential to open
them in at least for 30 % before first start
:
ź
opening the air stators of the diffuser 360°
must be done by two hands
in parallel
6. CONTROLS
Usage of automatic control dedicated to the devices of Reventon Group gives
great possibilities of adjusting the efficiency of the unit in different, depending
on needs, degree of its operation automation. We can offer the following:
5 control levels:
80-105-135-170-230 V
Voltage/ Frequency:
230 V AC / 50 – 60 Hz
Maximum current output (depending on model):
1.2 A, 3 A, 5 A, 7 A, 14 A
Protection:
thermal switch
Weight(depending on model):
1.45 kg, 2.5 kg, 4.5 kg, 5.5 kg or 10.5 kg
Degree of protection:
IP 54
Fan speed controller HC
designed to change the single-phase fan's speed voltage controlled in industrial
supply and heating systems. It is available in several versions. The selection
of the appropriate model depends on the number of the devices
that have to be connected to the to one regulator – the total
current
of the connected devices cannot exceed the maximum current flow
of the regulator.
Manual thermostat HC
c
ontrols operation of the heater
destratification fan. It switches the unit
off automatically
,
when the set temperature is reached
.
The total
current
of the connected devices cannot exceed the maximum current flow
of the thermostat.
Power supply/ Frequency
:
230 V AC / 50 – 60 Hz
Maximum current
:
3 A
Operating temperature:
0 - 40°C
Temperature control range:
10 - 30°C
Control accuracy:
<1°C
Degree of casing's protection:
IP 30
allows to connect a receiver with higher current consumption than permissible
current load of connected regulator.
Power supply/ Frequency :
230 V AC / 50 – 60 Hz
Maximum rated current:
16 A
Input
:
NO/COM
Input
:
SL Connection of a regulator
with the voltage relay 230 V
Dimension
:
47 x 47 x 20 mm
Relay Module RM-16A
Summary of Contents for TORNADO Series
Page 6: ......
