REVENTON TORNADO Series, Technical Documentation Manual

Page: 2 / 6

2.2 DEVICE DIMENSIONS
Ø h
TORNADO XS1 421 180
TORNADO XS2 466 190
TORNADO XS3 515 190
TORNADO XS4 5 67 250
TORNADO XS5 635 250
TORNADO XS6 705 250
1.INTRODUCTION
1.1 PRECAUTIONS
1.2 TRANSPORT
1.3 PACKAGE CONTENT
1.4 USE
2. DEVICE CHARACTERISTICS
2.1 CONSTRUCTION AND PRINCIPLE OF OPERATION
2.2 DEVICE DIMENSIONS
2.3 DEVICE TECHNICAL DATA
3. ASSEMBLY
3.1 GENERAL PRINCIPLES
3.2 MOUNTING HOLES
4. INSTALLATION INSTRUCTIONS
4.1 CONNECTION OF THE DEVICE TO THE ELECTRICAL SYSTEM
5. PRECAUTIONS & WARNINGS
6. CONTROLS
7. CONNECTION SCHEMES
8. TERMS OF WARRANTY
1. INTRODUCTION
Thank you very much for purchasing destratification fan TORNADO. We would
like to congratulate you on excellent choice. Please read and keep this manual.
1.1 PRECAUTIONS
The buyer and the user of the destratification fan Reventon Group brand should
read carefully the following instructions and proceed to the content
recommendations. Proceeding due to the following instruction guarantees
the correct usage and safety. In case of any doubts please contact directly
Reventon Group Sp. z o.o. [Ltd.]
. The producer reserves the rights to make
changes to the technical documentation without previous notice. Reventon
Group Sp. z o.o. [Ltd.]
is not responsible for the damages which occur due
to improper installation, not keeping the device in repair or using the device out
of line. The installation should be carried out by the professional installers,
who possess the qualifications to install these types of devices. The installers
are responsible for making the installation as instructed in the technical data.
In case of unserviceable please plug out the device and contact
with the authorized for repair person or the supplier. During the installation,
use, service and periodical inspections all regulations and safety rules
must be followed.
1.2 TRANSPORT
During the acceptance of goods, it is needed to check the device to exclude
any damages. During the transport, it is needed to use the proper equipment,
it is necessary to carry the device by two people. In case of any damages please fill
in the damage report in presence of the supplier.
1.3 PACKAGE CONTENT
- destratification fan
- instruction and warranty card
1.4 USE
In the heated high large-spaces the air mass is located in the upper part
of room, which causes the heat loss. Destratification fans also called the drop fans
or air mixers are used to save on heating. They steer the air back to work zone
at the same time they level out the air temperature in the high room, they also
limit the heat loss through the roof. They are used in production halls,
warehouses and logistic centres.
2. DEVICE CHARACTERISTICS
2.1 CONSTRUCTION AND PRINCIPLE OF OPERATION
Cylindrical casing: made of galvanized steel. It has mounting holes which make
it easy to assemble the destratification fan with e. g. mounting rods.
Diffuser 360°: made of galvanized steel. Using specially shaped air stators
the diffuser enables even air distribution in the room.
Axial blowing fan: made of galvanized steel. It has a single-phase motor
with the following parameters: protection degree IP44, rated current
0 . 65 - 3 . 5 A (depending on the model). The smallest device in the series
has diameter 350 mm while the biggest one has diameter 630 mm.
ENG
2.3
DEVICE TECHNICAL DATA
* measurement at the distance 5 m
3.
3.1.
During installation, ensure a free air flow to the device and do not restrict
the air stream supply. The figures below show the recommended distances
between the heater and building partitions:
ASSEMBLY
GENERAL PRINCIPLES
TECHNICAL DOCUMENTATION
Supply voltage [V] /
Supply frequency
[Hz]
Rated motor
current [A]
Motor speed
[rpm]
Motor power [W]
Protection
degree IP [-]
Net weight [kg]
Noise [dB]*
Maximum
vertical range [m]
TECHNICAL
DATA
Product code
TORNADO
XS1
Maximum
airflow [m3/h]
TORNADO
XS2
TORNADO
XS3
TORNADO
XS4
TORNADO
XS5
TORNADO
XS6
DT-XS1-1965 DT-XS2-1966 DT-XS3-1967 DT-XS5-1969 DT-XS6-1970 DT-XS4-1968
2200
6
230/50
0.65
1400
129
44
3600
8
230/50
0.82
1380
180
44
4800
10
230/50
1.15
1350
250
44
6400
12
230/50
1.75
1320
380
44
7600
13
230/50
2.55
1300
550
44
9700
15
230/50
3.50
1360
750
44
6.0 7.5 10.0 11.5 15.5 21.0
52 55 57 59 60 63