background image

11

90-DAY LIMITED WARRANTY

FCC STATEMENT AND INDUSTRY CANADA NOTICE

PLEASE DO NOT RETURN YOUR PRODUCT TO THE STORE.

 Revell  will repair or replace factory defects for 90 days from the date of 

purchase. This warranty specifically does not cover crash damage, misuse or abuse. To make a warranty claim, please contact our product 
support team at 

1-217-398-8970

 

option 6

 or e-mail us at 

[email protected]

If requested by Product Support, please send defective product to: 

Hobby Services, 3002 N Apollo Dr., Suite #1, Champaign, IL 61822

Please include a note about the problem, your contact information, and a copy of the receipt.

This warranty applies only if the product is operated in compliance with the instructions and warnings provided with each model. Revell  
assumes no liability except for the exclusive remedy or repair of parts as specified above. Revell  shall not be liable for consequential or 
incidental damages. Some states do not allow the exclusion of consequential or incidental damages so the above exclusion may not apply 
to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 

1. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2)  This device must accept any interference received, including interference that may cause undesired operation. 

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Remark: 

This device is in accordance with the digital device grade B limitation and the 15th regulation of FCC. This limitation requires reasonable anti-

interference protection around the residence. The device can transmit radio wave during use and can interrupt the mobile communication without proper 
installment. Interruption will occur for special device. If the device do interrupt the radio or television, please turn the device off then turn it on to adjust. 
Below are some resolution for your reference:

 Move the receiving antenna   

 Enlarge the distance between the device and receiver  

  Try to not connect the device and the receiver on the same circuit 

 Ask for professional help from experts

3. This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference 
Regulations of Industry Canada.

Summary of Contents for NANO Hexagon













Reviews: