14
15
14
English
English
5 STarT PreParaTION
4 ChargINg The helICOPTer
Attentio
n: The battery must cool down for 10 to 15 minutes before charging and
after every flight. Otherwise, the battery in the aircraft can be damaged. The charging
process is electronically monitored, but do not leave it unsupervised.
• Switch off the helicopter and the remote control.
• Carefully insert the charging cable in the charge socket of the helicopter
(4A)
.
The plug must be gently inserted in the charge socket – DO NOT USE FORCE. If the
plug is not correctly inserted in the charge socket, the helicopter can be damaged
and thus may, under certain circumstances, entail a risk of injury.
• Switch on the remote control, the power LED is continuously illuminated red
(4B)
.
• The charging process is complete as soon as the power LED is continuously
illuminated green
• After the charging process, switch the power switch to "OFF" and disconnect the
charge cable from the helicopter.
After a charge time of approx. 40 minutes with the USB charge cable the
helicopter can fly for approx. 6-8 minutes.
You can also charge your helicopter with the accompanying USB cable:
• Switch off the helicopter.
• Carefully insert the charging cable in the charge socket of the helicopter
(4D)
.
The plug must be gently inserted in the charge socket – DO NOT USE FORCE. If the
plug is not correctly inserted in the charge socket, the helicopter can be damaged
and thus may, under certain circumstances, entail a risk of injury.
• Insert the USB plug in an open USB port.
• The charging process is complete as soon as the USB plug illuminates.
• After the charging process is complete, disconnect the USB plug from the USB port
and the helicopter.
The thrust control (the left control on the remote control) must point down before
switching on
(5A)
. Then set the control switch of the remote control to the "ON" position;
the power LED is continuously illuminated green
(5B)
. Select the channel A or B with
the channel selector. Now set the ON/OFF switch on the right side of the helicopter to the
"ON" position
(5C)
. Place the helicopter on the ground so that the tail points toward
you
(5D)
. The LEDs on the helicopter begin to blink. The helicopter is now ready to start.
6 TrIM aDJUSTMeNT OF The CONTrOl
The correct trim is a basic requirement for fault-free flying behaviour of the helicopter.
The adjustment is easy, but requires some patience and feel. Please observe the
following instructions precisely: Carefully move the thrust control up and raise the
helicopter approximately 0.5 to 1 metre in altitude.
6A
If the helicopter begins to automatically
rotate clockwise quickly or slowly, rotate
the left/right trim adjustment anti-
clockwise until the helicopter no longer
rotates automatically.
If the helicopter automatically
rotates clockwise…
If the helicopter begins to automatically
rotate anticlockwise quickly or slowly,
rotate the left/right trim adjustment
clockwise until the helicopter no longer
rotates automatically.
If the helicopter automatically
rotates anti-clockwise …
7B
7 FlIghT CONTrOl
7B
Move the thrust control back for
landing or to fly lower. Only minimal
corrections of the controller are
necessary for a smoothing flying
behaviour of the helicopter!
7D
To fly backward, pull the control
back carefully.
7F
To fly along a right-handed curve,
carefully move the directional control
to the right, as long as the helicopter
tail is facing toward the pilot.
7A
In order to start or gain altitude,
carefully move the thrust control
forward.
7C
To fly forward, carefully move the
directional control forward.
7E
To fly along a left-handed curve,
carefully move the directional control
to the left, as long as the helicopter
tail is facing toward the pilot.
Up to two pilots can fly their helicopters simultaneously! To do so, proceed as follows:
• Pilot 1 switches his/her remote control on and selects channel A.
• Pilot 1 switches on his/her helicopter. After the LEDs on the helicopter are continuously
illuminated, the helicopter is set to Channel A.
• Pilot 1 sets his/her remote control aside without switching off the remote
control or helicopter.
>>
FlyINg MUlTIPle helICOPTerS SIMUlTaNeOUSly
2 reMOTe CONTrOl
2A
Infrared
transmitter
2B
Channel selector
switch
2C
Power LED
2D
Control switch
2E
Up/Down thrust
control
2F
Charge cable
compartment
2G
Forward and
backward flight
Fly left/right
2H
Left/right trim
wheel
3 INSerTINg BaTTerIeS
(reMOTe CONTrOl)
3A
Unscrew and remove the cover.
3B
Insert 6 x 1.5 V AA batteries and pay
attention to the polarity specifications,
as indicated in the battery compartment.
3C
Close the battery cover and secure
with the screw.
